Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi I am using BLE Mesh V4.0 and Stack V 16.0.0
I have included UART functionality in light switch server code to interface a sensor.Now upon receiving 5 bytes from UART...
I'm new with Nordic products, I bougth one nRF52840 and I tried to install Segger, to start programming.
I had a problem when I tried to open a SDK on Segger. When I try...
I'm using a custom nrf51822 board with S110 softdevice, and SDK 10. This board is used as SPI slave with BLE. I tried to estimate the stat up power consumption by reading...
Hi, we are developing a bluetooth device in my company that must transmit at a distance of about one kilometer. I saw that this soc has been tested up to 1300 meters. It's...
1. By the toolchain manager, the sdk connect and zipped toolchain were downloaded.
I used the downloaded SES to compile examples. For others, they can compile successfully...
Hi All,
My one of the old application is based on SDK11 and i found some issue data corruption with FDS module. After reading some post here regarding FDS issues and also...
Hello,
I am trying to evaluate the Channel Selection Algorithms (CSA) 1 and 2. From what I found on here, CSA 2 is enabled by default in SoftDevice stack, could you please...
Hello everyone. I want to create project from stracth for nRF52832. I use nRF52 DK. I couldn't find any tutorial for this. I create new project under nRF5 SDK 16.0 and specified...
I am using BT840F module from Fanstel which is based on nRF52840.
Currently I am having two EV-BT840 (Evaluation kit for BT840). I have modified 'pca10056.h' as per my board...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello Devzone,
I've been working on a system to set notifications on time ready for transmission.
The client sends a WWR package to my peripheral and I want my peripheral...
Hello,
Currently, I'm trying to flash my custom board that has nRF52832 with an uart application that I integrated buttonless DFU. I'm running into a problem where when...
1.nrf9160 is there an RF calibration parameter at the factory?
2. If there are calibration parameters, does burning mfw_nrf9160_1.2.0.zip firmware affect the calibration...
I have two devices here, So I combined three HEX files and burned them with JLink, and they don't behave the same. One starts the application normally, and one is always in...
