Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
I just brute force changed to "AWS_IOT", having the keys , and other config already in place after having tried the cloud sample code successfully against AWS
main.c
line...
During BLE startup call to nrf_sdh_enable_request(), nrf_atfifo_item_alloc fails and returns NULL causing a hard fault.
This sounds like an sdk_config.h problem but I don...
Dear all,
I have 10000 devices and I need to put a different value for every device, but I do not want to create 10000 firmware.
Is possible to do that with a tool? I...
Thanks for the reply. I can program my custom PCB from the nrf52 but I can't program the on-board nrf52832. It is always looking for Jlink to an external board. What tells...
I would like to modify the way the SPM is built, specifically by setting CONFIG_BOOT_BANNER=n but do not want to modify any files under the ncs directory. I tried the solution...
I have a multi peripheral sample I am trying to make work
I do a
BLE_NUS_DEF(m_nus) and BLE_HRS_DEF(m_hrs)
this will register two event handlers.
When an event occurs...
I have downloaded nRF5_SDK_12.2.0_f012efa and tried to test logging in examples but without success. Even if I compile an example where NRF_LOG_BACKEND_SERIAL_USES_UART 1...
Hi,
I'm trying to use an nRF52840 Dongle to make measurements from 4 SMT172 temperature sensors.
I developed a proof of concept on an nRF52840 DK, where I connect all...
Hi,
Finally i am able to build a basic TCP/IP server client, attaching the project here , i have some questions wrt modem and TCP/IP stack:
I see two different socket...
Hi,
I'm trying to increase Zigbee Tx Power to +8dBm by using the function nrf_802154_tx_power_set().
Digging into the code, I see that it is calling nrf_802154_pib_tx_power_set...
Hi,
I am using NCS 1.2 with Zephyr SMP_SVR example compiling with my own board DTS and using MCUBOOT
I have my own partitions configured in my DTS (attached down at the...
So I'm trying to start off development of my project using the PCA10040 development board. I have downloaded the SDK16 and built a couple of examples no problem using SES...
Hi,
I have a question regarding the frequency of the SPI peripheral of the nrf52.
According to the Product Specification v1.4, the minimum value for the frequency is 125kbps...
Hello Nordic Support!
The stop bit of the last character is short in the Uart output part, and the other MPUy cannot receive the character. How do I fix it until I send...
To the kind attention of Nordic support team,
I was wondering if it is mandatory that Host and Devices share the very same frequency table, with same size.
Is it possible...
