Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I'm using 3.6v battery and I want to read the battery voltage, can I get the power ping directly to the any ADC pin of nrf52833 ? Or it cause any damage to the ic ?
Hi,
In the attached study from Nordic and Energizer there is data regarding the discharge behavior of a CR2032 Coincell battery under different conditions. I wanted to...
We are using nRF9160 as the host MCU and Modem for communicating to server. If VDD_GPIO is powered by 3V external supply and SIM card is powered by VDD_SIM i.e. 1.8V Do we...
Hi,
I have a hex file generated by uVision Keil 5 IDE . I would like to combine this with the hex file form the soft device. These two hex files once combined would help...
Hi,
I would like to change the manufacturing data with time. My advertising_init function implements the following line
init.advdata.p_manuf_specific_data = &manuf_data_response;...
I've been using the nRF52840 DK to load the firmware into my custom nRF52840 board using nRF Connect v2.6.0 and programmer v1.0.2.
However, on another laptop when I install...
Hi,
We have developed a custom board using nrf52832 chip and currently everything like (BLE, TWI, ADC etc) is working fine but we are having issues with the UART. we have...
Hi,
We are using nRF52840 with nRF5 SDK ver 16.0.0 with Softdevice S113 ver 7.0.1.
We use the radio timeslot to implement low level radio comm with very tight timing requirements...
hi i am using this to capture the adc value data_ADC=adc_buffer[1]*(1024+gain_error) / 1024 + offset_error - 0.5; data_ADC_double=data_ADC*3.6/1024; MULTIMETER MEASUREMENT...
When I used nrF52832 mouse application, the SDK version was 15.3. When I connected to MacOS, I had to make several attempts to connect. Can you tell me why?
Thank you very...
Our nRF52832-based board is powered by a coin cell battery, and spikes in current can cause the voltage to drop. This is okay early in the battery's discharge curve, but as...
The communication between the UART peripheral and the nrf52840 works fine until some device connects to the nrf device via BLE. Using a digital logic analyzer I'm able to...
hello
now we want to use nrf52840 qspi interface to connect with fpga. we have a question:whether nrf52840 could be used as qspi slave, and fpga used as master?
if it...
