I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi all,
can i send a scan request from an nRF52840 dongle using the nRF Connect - Bluetooth Low Energy software? I need this during development of my application where i...
Hi
I am seing framing errors when receiving using UARTE.
It is not external hardware, I have checked with different other interfaces and measured timing, no problems there...
Hi
I want to ask a few question.
When the phone sends a specific signal after connecting to the MCU, the MCU is sending data in real time.
When the power is turned...
Hi,
I was trying to find out if it is available to have authentification before connection and I found this link and it makes sense to me but that Q&A has been over 4 years...
Hello!
I use Zigbee CLI example and multi_sensor example on nRF52840. (examples/zigbee/experimental/cli/cli_agent_router and examples/zigbee/experimental/multi_sensor) ...
I have nrf52840 dongle and sdk nRF5_SDK_17.0.0_9d13099.
I would like to know, is there is an example in which, Advertisement Data is stored in flash memory and reading and...
I USE 9160 with i2c ，send data. then it tips :
[00:02:07.716,918] [1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0[0m
what is wrong ?help me ,thank...
NOTE: This is related to the following issue: https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
--------------------------------...
Hi,
I would like to read data from sensor and send it over BLE to nRF connect. Unfortunaly, something went wrong while reading the data by TWIM.
I´m using SDK16. ...
Hi Sir or Madam,
I tested examples\zigbee\light_control demo recently and I want to test install code function based on this example, the first step is I add install code...
Hello,
I’m interested to replace a part of my project by a dongle. The current prototype of the project comprises two Nordic nrf52840-DK boards, an Analog Devices Eval,...
Hi,
during the test of the trasmission, in my phone I have seen the figure below:
As you can see the trasmission is every 2 seconds and I want to change this time trasmission...
I was looking through the nRF documentation as well as some of the Thread documentation and I was unable to find a definitive answer about the IPv6 fragmentation support within...
Hi
I want to purchase NRF52810 parts pre-programmed with my Firmware. Is this an option you provide and can I reprogram them via the Debug port if required.
Hi,
I am trying to interfacing the IMP34DT05 Microphone with the NRF52840. I can see in the DSO that CLK pulse is generating in the NRF52840, but there no data pulse from...
