I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hello,
I try to add the BLE-Template code into my existing program code, but I get the following linkage error. I have defined the following flash_placement.xml for my Segger...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
Hi,
Add BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event handle at ble_lbs service in example of ble_app_blinky. but when client read the characteristics 1524 or 1525, no BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
Environment: Windows 10 nRF Connect SDK 1.4.0 I followed all of the steps described in nRF connect SDK documentation and tried to build "Blinky" sample from zephyr as shown...
use s132 on NRF52832
when i used sd_ble_gap_connnect () to connected peripheral device,it return NRF_ERROR_INVALID_ADDR
the addr copyed in scan_evt_handler() by NRF_BLE_SCAN_EVT_FILTER_MATCH...
Hi ,
I have made basic binary sensor based on light bulb project,
wanted to add default BIND-TO-Gateway ( Short address 0x000). Gateway is CLI_AGENT .
I am try to add...
select at_client folder
west build -b nrf9160dk_nrf9160ns -p
shows this warning
```
warning: The choice symbol LTE_NETWORK_MODE_NBIOT (defined at /Users/paul_tanner...
Hello, we are using a usb dongle where we have a NRF52840 and RFX2401 PA+LNA frontend. The latter can be controlled with TX_EN and RX_EN pins. Please see attached schematic...
Hi there,
I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. Everything except one single thing is working. I've just implemented FDS...
I have installed the sdk v 1.4.0 via the toolchain manager (nrf connect 3.6.0). I am using windows 10.
Here are my problems :
First I dont have the launch ide button after...
Hello Team,
We have already done the PoC for the Openthread network. I have created a border router using nRF52840 as an NCP and multiple nRF52840 end devices.
Now my...
If I have a firmware project working reliably on the nRF52810, is it possible to build a single firmware image that will run on both the nRF52805 and the nRF52810? I'm not...
Hi,
I was trying to program my board using SEGGER, but it doesn't seem to be working (log provided in the picture below)
/resized-image/__size/320x240/__key/communityserver...
