i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
As we are in design phase of our custom board based on nRF9160, can you please let us know what all pins needs to be exposed in our design for collecting modem traces...
Hi Team,
I am trying to integrate a scheduler feature for my Thingy 91 using a nRF9160 DK kit. I searched for a few examples and found the one below in the link:
https...
Hello everyone,
I am developing a simple BLE node with an I2C sensor on it. Basically I just need to send over BLE the measurements made by that I2C sensor every minute...
Hello,
I am new to the Nordic environment and am trying to set up a beacon to scan and advertise using BLE.
I used the beaconing example ( https://github.com/NordicSemiconductor...
Hi, I have the same issue as in here: https://devzone.nordicsemi.com/f/nordic-q-a/62676/2-spi-devices-nordic-nrf52382 but for me the Debug/Release-toggle does not work. I...
Hi,
Can you confirm if TWI is supporting I2C clock streaching? Or and workaround to handle such a case.
As in attached picture is slave device requirements. Slave device...
Hello,
I’m using keil compiler.
My configurations are nrf51822ac/SDK12.3/s130_nrf51_2.0.1_softdevice.
I’m trying to migrate to SEGGER studio.
I’m referring to the...
In my case, I have 50+ devices as sensor and advertising measurements every 10 seconds, ADV_DURATION = 120s, use the 1E FF manufacturer data and self defined payload protocol...
i want to implement the nfc connection of pairing the nordic nrf52840 using SDK ver 15.0.0.
Can anyone help me in implementing this feature? because I'm new to this pairing...
Hello, all
I would like to ask about flash memory write errors.
When using version 12.1.0 of sdk, I was able to r/w to flash memory normally by using the sd_flash_write...
Based on sdk12.3, use 51-dk (51822) to run the ble_app_hrs routine. Use ios mobile phone to connect the device, it will automatically disconnect after 30 minutes, the disconnection...
The problem is not being able to connect to the device from an iPhone SE while the app is in background mode. We have an iOS app written in swift, which uploads data from...
Hello, I have couple of NRF52840 devices that i purchased from Adafruit. I wanted to use them with Alexa Gadgets Toolkit via BLE, however with no previous experience with...
Hi,
I'm working on building a zigbee multisensor device using a nrf52840 module. I'm heavily relying on the multi sensor example and so far I've been able to add temperature...
