I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
I'm beginner with nrf chips.
I have a custom board with ntf52840 module. I connect board to stlink via swd interface, then check:
st-info --probe Found 1 stlink programmers...
I would like to perform observer role scanning i.e. passive scanning. I am using nRF52832, S132, SDK 15.2.0. I am trying as follows.
NRF_BLE_SCAN_DEF(m_scan);
static...
I am using the SDK5 development kit with Segger for a BLE application.
I found the Service for SES but the SDK doesn't seem to include the Pulse Oximeter service.
I would...
We are developing hardware to work as a AirMouse (Gyroscope based working mouse)
I am using SDK16.0 SES
I have seen that HID Mouse example
and i implement gyroscope...
I have bought a BLE Micro. ( www.seeedstudio.com/Seeed-Micro-BLE-Module-w-Cortex-M0-Based-nRF51822-SoC-p-1975.html) 1. I downloaded "nRF Connect App for Android" on the phone...
Hi there,
I've recently purchased an nRF52840DK with the 52840 SoC and I'm wanting to develop Bluetooth Mesh apps.
I'm on Mac OS X. Should I begin with the nRF52 SDK or...
Hi,
I just got the brand new Thingy:91 and would like to program it with an application earlier developed for the nrf9160 DK .
Further I'd like to use the Link Monitor...
Hi All,
Recently I have been working on nrf9160dk board. The use case is to have nrf9160 work as a serial LTE modem with GPS functionality. I have the following link https...
Hi,
I have implemented my own Vendor model, using the light switch client/server as a starting point. The model allows to send byte arrays. Since I have used the generic...
I am using SDK v16, SEGGER to program on my nrf52832 SOC for our project. I need to save a few variables to the flash memory. These variables will hold the status of the device...
Hello,
we are using SDK version 15.3 and mesh SDK version 3.2.0, on a nRF52840 DK board using the Segger Embedded Studio IDE version 4.52 (64-bit).
Our goal is to add...
Hello,
I followed this tutorial in order to familiarise with the code and understand better what is going on. Now, my question is the following, regarding challenge 2 :...
Hi,
I'm using latest master branch of nRF Connect SDK and pre-released modem FW 1.1.2 which is including ANT->AUX switching. I'm developing a firmware for a custom board...
Hello,
I notice that Thread examples with Softdevice (nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b) works fine for a PCA10056 but not on a PCA10059. When I had tried...
I am using nrf52832. I have one led connected to the gpio 25 through the active low condition.
i am trying to configure gpio 25 using this " nrf_gpio_cfg_pin_output(25);...
