Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
Hello, I just brought this board and I was playing with it but I'm unable to get it working, I'm using platformIO IDE and I have configured it to use Arduino framework but...
I've been having a ton of issues getting any of the application code to run on my Thingy91. Just tried updating the Modem FW to 1.2.2, however I'm not able to place my Thingy91...
Hi:
52840 with softdevice, I use External low frequency oscillator (32.768K) ,the system run normal,but some days later,system can't run. So,I find the problem，the problem...
The Bluetooth Core Spec version 5.2 says that the " maximum number of CISes in a CIG shall be 31."
Can the nRF52840 support 31 concurrent CISes in one CIG? If not what is...
I want to load the GPS routine project of 9160, but it fails. The error prompt is as follows:
one step
When I click OK, the following prompt appears
two...
Hi,
I have nRF52833 and nRF9160 on my custom board. Due to limited space available, trying to use a common SWD interface between the two SoCs. As follows: 1) SWDIO and SWDCK...
I add the MAC of acquisition device in the broadcast initialization of nrf52810 serial port routine, it can display complete. But I added the Mac to the template broadcast...
Hi ,
My firmware is almost done, and now is the time to optimise power cunsomption.
First, my software has a special mode. Each day it wakes up, communicate with a sensor...
Hello,
We are developing products with nRF52810 MCU. There are only 100 bytes ROM left now. We hope to update bootloader via Buttonless DFU in single bank way. Is it available...
I want to use the four peripherals UART0, UART2, UART3, and I2C_1 on nrf9160. When I was building the project, I encountered the following error.
Here my prj.conf
...
Hi,
I received a Thingy91 and am unable to commission it to nrFCloud.
The Thingy91 skipped orange breathing as mentioned in the manual here (step 4). It went directly...
Hi! I'm running a project with an nrf52 chip for which we use the JLink as the interface. I've been using my setup a lot for the past year. The other week, every LJink command...
Hello,
i'm trying to understand how the management of the SS pin is (or has to be) performed when using nrf9160 as SPI master.
In this post Håkon said that:
"Most driver...
Hi,
I using the radio test example on the pca10040 with nrf52832 EVB.
And set the radio test to Tx, the parameter as below:
Data rate: NRF_RADIO_MODE_BLE_1MBIT TX power...
