Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
Hi,
I have a problem with coap response. I use iot coap library.
Client send nonconfirmable coap message with payload to broadcast addr
Server get payload and send nonconfirmable...
I am getting the Following error after connecting the JLink
I followed the following procedure
What am I doing wrong? DO I need to install anything else?
Hey All,
I ran into an issue on the nRF Connect SDK trying to get a nRF52840 advertising using CODED PHY. I figure it's not fully implemented yet are there any updates on...
I advertise as
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE
BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED
This posts suggests I may have not really disabled...
I am using an NRF53 DK board with nRFConnect/Zephyr 1.3.0. I need to define the UART pins I will use in a .overlay file but I would like to NOT define any flow control pins...
Hey
I am working on nRF51822 SDK12, S130
I have encountered a problem when connecting and disconnecting from the device at a fast rate, occasionally comes an event in...
Hello,
We integrated latest released version of "pc-ble-driver.py" & "nrfutil" in our custom linux os running on ARM 32bit based custom board (B1).
pc_ble_driver_py :...
Hello,
Our design uses Laird's BL652, which uses nRF52832. I need to calculate the maximum clock drift of timers given the crystals used in our design. Our application uses...
Hi,
When I tried to use BLE5.1 phase data to achieve direction finding, I found a phase shift between reference period and the first slot, as the below graph shown:
...
Hi DevZone!
I would like to use nrf9160 for sending/receiving data by interfacing it with my microcontroller over UART and sending AT commands. I have a nrf9160 Feather...
Hello, support team.
In my SDK, I created two app timer.
What I expected is
- 1st handler called every 1 msec.
- The other handler called every 100 msec.
But...
This "BUG" is observed on nrf52840 DK (chip version is version 2 from *(UINT32*)0x10000134UL).
When NRF_RADIO is set to TXADDRESS 0 and RADIO_PCNF1_WHITEEN_Enabled...
...
Hello,
I am using VS Code 1.48.2 and building the C++ application code on nRF52840 dev board using "west" commands.
I have the following structure
project_directory...
Hi,
With the latest SDK (17.0.2) I try to use the SAADC module in blocking mode but when I call <nrf_drv_saadc_sample_convert> an ASSERT is always triggered in <nrfx_saadc...
Hi. I'm developing central device for IoT system.
Everything is going well, but there are some problems on connection precedure.
I tried to conenct 7 pheriperal(nRF52832...
