We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi there, I want to use CppUTest on the nRF52 to start developing my personal and not so personal projects. I am using the SDK for nRF52, with PCA10040's board. For the moment...
My nRF9160 is plugged into a Raspberry Pi and located somewhere far away from my office, where it can receive an LTE Cat-M signal. I'd like to update the LTE firmware, but...
Hi,
Recently we got Thingy91 and testing the GPS.
we have our custom nrf9160 board and GPS is working and getting coordinates in outdoor.
Im running the sample GPS application...
Hey All,
Due to my findings with this ticket ( https://devzone.nordicsemi.com/f/nordic-q-a/62255/lte-link-monitor-timing-out ), I decided to try and compile the LTE Link...
Hi All,
I am using the light switch example and have modified it a bit to send packets of data. I am able to send data from the client to group address, by setting the...
I have two beacons which are UUID filtered successfully.
I am trying to fetch major but this cannot be done just by putting an offset to p_adv_report->data.p_data. I noticed...
Hi,
nrf52 using from ble-peripheral-> ble_app_uart examle
In that ble_app_uart example receive the data from the android is ok.
But,i want transmit array type of data...
Hi.
setup is 52832, S332, SDK 15.3.0.
issue is about reset voltage.
I use CR2032 for power supply.
repeat fast put on and put off CR2032 on custom board, sometimes...
Hi All,
I am using nRF52382 and sdk 15.0. I have two SPI devices using separate pins. They work just fine separately, when I try to enable two instances I get compilation...
Hi,
As mentioned in "nRF52840 Product Specification v1.0", I have setup the high voltage mode, and use VDD as an external power of 3.3V by setting NRF_UICR -> REGOUT0 to...
I want to use 52811 as central deice, which SDK and SoftDevice should I use?
https://www.nordicsemi.com/Software-and-tools/Software/S140
It says: SoftDevice S140 is a...
Hi,
I’m looking to build the Bluetooth HCI-RPMsg sample for nRF52811.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/bluetooth/hci_rpmsg/README...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
Hello,
Development to blink LED only on Nordic Thingy 52 has been started after referring the following one of the post from Nordic Devzone. https://devzone.nordicsemi.com...
