I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I used the Adafruit Bluefruit NRF52840 LE and added some simple code to this existing timer/counter for pulses: https://devzone.nordicsemi.com/f/nordic-q-a/62633/nrf52-timer...
Hi,
While going through some of the peripheral examples in 'nRF5_SDK_17.0.2', I found it puzzling to see that
the legacy (nrf_drv_*) and nrfx_* drivers are simultaneously...
Hi all,
trying to get CAN-bus support under Zephyr. Have a seed CAN bus shield link connected to PCA10040. The shield use SPI2 connected to MCP2515 CAN controller link ...
Hello
Is it possible to use the qspi of the nrf5340 for custom spi devices? I need the quad spi for the 96MHz speed which the normal spi does not have.
I know of the nrfx...
Hi there,
I am using the Nordic SDK 16.0.0 on an nRF52840 with FreeRTOS. I am quite familiar with using FreeRTOS, but hadn't needed to delete a task until recently. It seems...
Hi everyone,
How could I disable notifications from a characteristic when the peer is get disconnected from the the peripheral? My problem is that when notification are...
Hi,
I was investigating the registers of the nrf9160 using segger embedded studio and found POFCON, which is not mentioned in the documentation.
Can you provide...
I need to add some IPSO objects for our project. It is not quite obvious to me if I need to create modules similar to i e ipso_temp_sensor.c or if it would be enough to use...
Hello, guys!
We are desiging our custom board based on nRF9160 SiP. The board will be battery powered. Li-Ion rechargeable batteries will be used to supply the device. ...
Hi to all,
i am developing a device based NRF52840 soc, and i want to implement a device that need to store some public/private key in somewhere. i know that cryptocell...
Hello,
I am developing on the NCS 1.4.0 and on a NRF9160DK. I am working on the asset_tracker example and I noticed that the code sends an assisted gps request to NRF...
Hi,
I am using app_uart library with Tx and Rx FiFo. I want to check how much space is available in the Tx FiFo at any time, and similarly how much space is filled in the...
Now I am using Nrf52832,SDK15.0.0, S132,
When we developed the DFU OTA function APP, we encountered some abnormal situations: it could not get out in the bootloader mode...
HI,
I am trying to read the payload length of the data coming in a topic via MQTTSN over OpenThread. In the event handler, I am getting the event and trying to get the length...
