I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi,
I have a problem with coap response. I use iot coap library.
Client send nonconfirmable coap message with payload to broadcast addr
Server get payload and send nonconfirmable...
I am getting the Following error after connecting the JLink
I followed the following procedure
What am I doing wrong? DO I need to install anything else?
Hey All,
I ran into an issue on the nRF Connect SDK trying to get a nRF52840 advertising using CODED PHY. I figure it's not fully implemented yet are there any updates on...
I advertise as
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE
BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED
This posts suggests I may have not really disabled...
I am using an NRF53 DK board with nRFConnect/Zephyr 1.3.0. I need to define the UART pins I will use in a .overlay file but I would like to NOT define any flow control pins...
Hey
I am working on nRF51822 SDK12, S130
I have encountered a problem when connecting and disconnecting from the device at a fast rate, occasionally comes an event in...
Hello,
We integrated latest released version of "pc-ble-driver.py" & "nrfutil" in our custom linux os running on ARM 32bit based custom board (B1).
pc_ble_driver_py :...
Hello,
Our design uses Laird's BL652, which uses nRF52832. I need to calculate the maximum clock drift of timers given the crystals used in our design. Our application uses...
Hi,
When I tried to use BLE5.1 phase data to achieve direction finding, I found a phase shift between reference period and the first slot, as the below graph shown:
...
Hi DevZone!
I would like to use nrf9160 for sending/receiving data by interfacing it with my microcontroller over UART and sending AT commands. I have a nrf9160 Feather...
Hello, support team.
In my SDK, I created two app timer.
What I expected is
- 1st handler called every 1 msec.
- The other handler called every 100 msec.
But...
This "BUG" is observed on nrf52840 DK (chip version is version 2 from *(UINT32*)0x10000134UL).
When NRF_RADIO is set to TXADDRESS 0 and RADIO_PCNF1_WHITEEN_Enabled...
...
Hello,
I am using VS Code 1.48.2 and building the C++ application code on nRF52840 dev board using "west" commands.
I have the following structure
project_directory...
Hi,
With the latest SDK (17.0.2) I try to use the SAADC module in blocking mode but when I call <nrf_drv_saadc_sample_convert> an ASSERT is always triggered in <nrfx_saadc...
Hi. I'm developing central device for IoT system.
Everything is going well, but there are some problems on connection precedure.
I tried to conenct 7 pheriperal(nRF52832...
