Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
I am finding that bonds are not saved to flash when using the latest SDK and S110 SoftDevice.
To test this, I am using the HTS example code, and the Master Dongle.
I open...
Hello,
I discover and connect my nRF51822 service. It can be peripheral and Communication read/write data. but have some issue for disconnect/reconnect .When My app for iOS...
Hello,
I am planning to develop a system where there are 16 bluetooth LE devices (nRF51822) each one sending/receiving data via Bluetooth LE (~30 kbps) to/from an access...
Hi !
I know that there is a way of OTA updating the nrf8200 application. But i'm not sure if this process requires aditional hardware like it happens when using the BLE113...
Hi All,
I am able to successfully connect to nrf51822 EK using BlueZ 5.12 and can read many of the characteristics except for the temperature value.
I understand that...
Hello
I have a project about voice communication.
Trying to do bidirectional voice communication, is there any possible to work on nrf51822
It means whatever via Bluetooth...
Hi,
I have version 2.0.0 of Evaluation Kit. I was waiting for the new SDK and SD 6.0.0 but I have seen the warning about hardware versions. I have to finish a SoftDevice...
I'm a noob in this alley! it is my first time working with Nordic products. In the past I used Energy Micro and ST Micro.
I downloaded Keil 4.x from ARM website. Then I...
Hello,
I am developing a project using nRF51922 and S310, and the project is built using SDK4.2.2 with the modifications mentioned in a document called "nRF51922 - ble...
We are looking to understand the internal working of the nRF51822 firmware (MEFW_nRF51822_0.9.0_firmware.hex). If someone can share the original code or the basic block diagram...
Hi folks,
I want to match my IFA PCB antenna to the nRF8001. As Harald recommended a couple times, I am going to measure the antenna of the final PCB with a Vector Network...
Hi All,
I use the 51822 DK to do the current measurement and do as the DK user guide 5.1.8 current measurement.
I just use the __WFI() to make the 51822 get into idle...
Hi!
I must match NRF24L01 to 40+j48 ohm antenna. This is not my design, so
no possibility to change. I have PCB antenna, that was measured to be 40+j48 inside
enclosure...
I have some non-volatile storage routines that I have written before, but the new SDK V5.0.0 has this pstorage module that is supposed to replace it, right? How do I migrate...
I use 51822 nrf6130 "device_firmware_updates" example to update AP. When I build "dfu_dual_bank",the update will success. But when I use "dfu_single_bank",the update will...
