I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
We're needing a lot more RAM than what nRF91 has, does current nRF Connect SDK support parallel PSRAM on Zephyr somehow or is the development on a roadmap?
Hi there, I want to use CppUTest on the nRF52 to start developing my personal and not so personal projects. I am using the SDK for nRF52, with PCA10040's board. For the moment...
My nRF9160 is plugged into a Raspberry Pi and located somewhere far away from my office, where it can receive an LTE Cat-M signal. I'd like to update the LTE firmware, but...
Hi,
Recently we got Thingy91 and testing the GPS.
we have our custom nrf9160 board and GPS is working and getting coordinates in outdoor.
Im running the sample GPS application...
Hey All,
Due to my findings with this ticket ( https://devzone.nordicsemi.com/f/nordic-q-a/62255/lte-link-monitor-timing-out ), I decided to try and compile the LTE Link...
Hi All,
I am using the light switch example and have modified it a bit to send packets of data. I am able to send data from the client to group address, by setting the...
I have two beacons which are UUID filtered successfully.
I am trying to fetch major but this cannot be done just by putting an offset to p_adv_report->data.p_data. I noticed...
Hi,
nrf52 using from ble-peripheral-> ble_app_uart examle
In that ble_app_uart example receive the data from the android is ok.
But,i want transmit array type of data...
Hi.
setup is 52832, S332, SDK 15.3.0.
issue is about reset voltage.
I use CR2032 for power supply.
repeat fast put on and put off CR2032 on custom board, sometimes...
Hi All,
I am using nRF52382 and sdk 15.0. I have two SPI devices using separate pins. They work just fine separately, when I try to enable two instances I get compilation...
Hi,
As mentioned in "nRF52840 Product Specification v1.0", I have setup the high voltage mode, and use VDD as an external power of 3.3V by setting NRF_UICR -> REGOUT0 to...
I want to use 52811 as central deice, which SDK and SoftDevice should I use?
https://www.nordicsemi.com/Software-and-tools/Software/S140
It says: SoftDevice S140 is a...
Hi,
I’m looking to build the Bluetooth HCI-RPMsg sample for nRF52811.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/bluetooth/hci_rpmsg/README...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
