Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
I use pin SDIN, SCLK, CS, DC.
but how do I connect the pin nrf51822
spi_master_example is
#define SPIM0_SCK_PIN 25u /**< SPI clock GPIO pin number. */
#define SPIM0_MOSI_PIN...
I have been reading about code regions in the nrf reference manual and understood about CLENR0 and how to use it. I have however, two questions
What is Pre Programmed...
I am using the SPI Slave port in the nRF51822 and am always transferring 20 bytes. No matter what I do, it seems that the status register in the IRQ says that I got a TX buffer...
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hi,
I need to be able to communicate between two boards via UART. I had a look at the example from Ole provided here: devzone.nordicsemi.com/.../ as well as other references...
Hello,
I am wondering if I can use any 128 bit UUID value.
For example, in the example uart project, Nordic UART Service = 6E400001-B5A3-F393-E0A9-E50E24DCCA9E is used...
If I want to stream samples up to the nRF Toolbox HRM iOS app plot, what is the fastest that I can call ble_hrs_heart_rate_measurement_send in firmware assuming I have nothing...
Hi,
I'm using nRF51822 Development Kit and trying to program softdevice with nRFgo Studio. The file to program is C:/Program Files (x86)/Nordic Semiconductor/nRFgo Studio...
I'm using S110 version 7.1.0, but need a way to validate in general which S110 and which SDK version I have associated with this .uvprojx project.
Much of this stems from...
I'm running the ble_app_beacon_s110_pca10028 example on my NRF51 dongle. The good news is that I see a beacon transmission on my iPhone 6 on this "Pally BLE Scanner" app....
We are developing a new BLE tag product using the nRF51822. We would like to assemble the PCB and battery in a single operation then program the product sometime later. Can...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
I'm trying to use RTT for debug printing and having some trouble. I'm using the nrf51-ble-app-lbs example app that goes with App Note 36. I've added the RTT code from www...
Hi,
iOS device uses random private resolvable type changes own bluetooth address address every 15 minutes as long as I know. Can I see the transittion just to change the...
