here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I changed the IO of the SPI and could not receive the data.
Hardware: nrf52832 DK two
Software: nRF5_SDK_17.0.2_d674dde\examples\peripheral\spi and nRF5_SDK_17.0.2_d674dde...
Hi,
I'm developing an application for the nRF52840 that uses 3 SAADC channels. In particular, the channels are configured as below:
I'm able to get the samples from...
It is unclear, for both the Thingy 91, version 1.0.2, and nRF9160-DK, version 0.8.3, if they need bias-tee's for use with an external active GPS antenna. Also, what about...
Hello, I have problem and I hope you can help me.
I have 3 sensor nodes. every node has an IMU sensor and nRF52840 microcontroller. These nodes send the IMU data to the...
We bought 4 NRF5340 PDK and trying to setup BLE mesh. As suggested in the getting started guide, there are two BLE mesh example samples from nordic and zephyr. However, for...
My code uses the nrfx SPIM driver. This gives you the option to use interrupts or not. Interrupts are great for long message transfers, allowing sleep while waiting for the...
SDK 14.0 +nrf52832:
We use phone to send command to our toy(nrf52832) every 100ms to control a motor accurately，mostly toy received command is long than 100ms(more than...
Hi, Is it possible to order nRF5340 QKAAD0? This one is on DK and the last IC version? As I can see, your distributors e.g. Mouser only have nRF5340-QKAA-AB0-R/R7 but this...
Hi,
I am using nrf52832 development board with s132 softdevice and SDK17. I want to add the DFU service to this application so that I can update the firmware to the device...
Hi,
In the Enhanced Shockburst User Guide, there is a brief discussion about the required bit pattern of 1st on-air byte of the base radio address
(which immediately follows...
If I use nRF Connect to connect to the Peripheral and the Subscribe to Notification Characteristic I can see in the "Enabling notifications" in the log (however no notifications...
Hello
I use sdk v17.0 and nrf52832.
I'd like to use 1-channel PWM and 2-channel PWM. However, an error is output from the pwm_enable when using these two together.
...
Hi,
Following are my working environments:
Product: nrf51422 Evaluation Board
SDK: nrf5 SDK v10.0.0
IDE: Segger Embedded Studio
Programmer: Segger J Link
I was...
Hi,
We have a device that is using Nordic's ESB protocol. We want to use different frequencies to avoid collisions and for that we also need dynamic frequency handling....
Hello,
I have two questions:
How do I access the gpio pins of nrf52840 dk? what example program from nrf5 sdk can I use as example?
Is there a simpler example program...
