void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello
To calculate the definite yaw value of gyro, I would like to use the mpu9250 with magnetic sensors. I used Martinsbl's nrf5-mpu library when I used mpu6050, can I...
Hi there,
what is recommended strategy to read/write data on uart?
Taking from sample, read byte-by-byte, on 115k, sometimes data are truncated.
Is there a possibility...
Hello,
I developed a thread network using the latest SDK for Thread v4.1. I also have the latest OpenThread Border Router running.
I cannot ping Google IPv4 from my Thread...
Hi,
I'm using nrf52840DK as a central device (sdk16 ble-app-uart-multilink-master) and my peripheral device is bt840 chip(sdk15.2 ble_app_uart_pca10056_s140).
My peripheral...
hello
i have 2 questions about System on mode:
i testing different types of power comsuption modes, i've tested RTC wake-up for system on mode, but i want to try to wake...
Hi, I want to run unit tests on an actual device (nRF52dk) - is it possible? When I'm trying to run `west build -b nrf52840dk_nrf52840` on `ncs/nrf/tests/unity/example_test...
I ask for your understanding of my short English. I am a student studying in Korea.
i using sdk 15.2 and nrf52840 dongle
When using the example of usbd_ble_uart of peripheral...
Hi,
im use the example of nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard
and i change the code of static void hids_init(void) like this:
and...
Hi
i have installed segger emstudio and almost all dependencies but still can't able to build a project. my main target is to work with nrf9160 dk but without an hardware...
Hello!
I'm working on a project with the new nRF5340 & Zephyr and I'm trying to get two SPI peripherals on the same bus sampling data correctly. It's a simple program thus...
Hello,May I ask you a question?
Hardware model: NRF51822 SDK version: SDKv9.0.0 SoftDevice:s110.
I used the interface in the pstorage.c file to realize the storage of...
Hi there,
I'm just trying to start to code my project. I want to stream 48k 16 bit audio from one nrf52840 dongle to the other one. I only need one way transfer.
I have...
Hi,
I want to use dtm project to test RF PHY performance about NRF5340. But after downloading dtm project and empty app project, NRF5340 can work normally from output RTT...
Hello I use nrf52832 and sdk v17.0.
I'm testing the firmware using custom pcb. Sometimes it stops altogether if there is an error in the firmware during the test.
The...
