I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi,
On Nordic SDk 15.0, I have observed that USB CDC ACM Example is not working in interrupt mode on nrf52840 Evaluation kit.
But I have tested USB CDC ACM Example in...
I'm experimenting with nRF52840 DK
However, using break points in the main loop causes 'app_error_fault_handler'.
using the iar compiler. What's the cause?
Hi~
I have a question about the SAADC.BLE Connect Mode. When I turned on Saadc LP mode, the power dissipation was 0.02mA for single-channel sampling, but 0.5mA for dual...
Hi All,
I have looked through the devzone and cannot find a solution to this. I am using the nRF52832 SDK 15.2. Working with a BNO080 IMU over TWI.
I need to read more...
I have bought new thingy 91 from mouser. Com. I burnt the latest pre complied hex file for assist tracker. I am getting all data except gps.
it is not getting connected...
I have a custom firmware developed on a nrf52832 SoC. I would like to know if i could see nrf logs such as nrf_log_info and nrf_log_debug via bluetooth? if this is possible...
Hi!
I want to use a TensorFlow Lite for microcontrollers model in my existing project built on top of the nRF5 SDK. However, as outlined in the nrf-tensorflow example ,...
Hi ,
I has been using NRF9160's AT client mode to connect with CMW500, however I found some problem.
The following is the command log that I used to send via UART. However...
I'm working on code that needs to discover services on the central so I'm using ble_db_discovery_start. However, I notice that if the connection handle passed into this does...
I am trying to measure frequency of a gpio pin. I am using the code from the below thread -
https://devzone.nordicsemi.com/f/nordic-q-a/9036/measuring-input-gpio-pin-frequency...
Hello,
About 2 months ago I upgraded my project to SDK 17.0.0 (from SDK 15.0.0).
When I opened the datasheet recently I found that a newer version - SDK 17.0.2 is now...
Hello,
Im trying to implement FOTA on the nrf9160. Currently my first version is working however I would like to decrease the amount of data used in the process. According...
Edited: It appears any use of NRF_CRYPTO_BACKEND_CC310_BL breaks joining.
Environment: nRF52840; SES; nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
I am implementing Thread...
Hi Support Team,
For the recent DFU issue "some Android 10 can not connect to the device during the DFU" ( https://github.com/NordicSemiconductor/Android-DFU-Library/issues...
I have 2 characteristics in a single custom gatt service.
There are 2 issues -
1. If I dont enable notifications on char 1, I dont see any data on char 2, even though...
