VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hi everyone,
I am trying to understand the Memory layout of nRF52840 SOC in order to apply RAM retention into specific section. Looking the memory layout at pg 21 of the...
Hello Nordic community,
I have a nrf52-DK with SDK15.2.0 and I'm trying to communicate with ST HTS221 sensor. I have the original STEVAL-MKI141V2 evaluation board.
I...
Hello,
I was wondering what examples we have in nRF Connect SDK (NCS) for firmware updates over BLE and serial (receiving an image from another device over UART). Specifically...
Hi
I have bought NRF5340-PDK board to study BLE-MESH. I found that there is 2 development tool in Nordic website
1. nRF connect SDK
2. nRF connect for Desktop
...
Hi,
I have a custom PCB that uses the nRF9160 and an RGB LED. I want to drive this LED with PWM but it uses an active LOW style of GPIO drive. I have been able to use normal...
I'm using nRF52832 with SDK v15.3 and S332 v7.0.1.
The Wireshark capture snippet shows our product connected to an iPhone using our proprietary service with a single notification...
I am using the nRF SDK v15.3.0 example project ble_app_rscs on a PCA10040 development board. I am trying to determine the functionality I need to port to my pre-production...
I would like to get timestamps with ms accuracy in order to compare it with power measurements taken simultaneously. The +CCLK command accuracy is in seconds and there are...
Hello, I am currently working on a nr52840 s140 Sdk 17.0 (dev kit) and a m using the peripheral/uart example code.
The UART TX & RX works perfectly when connecting to a...
Hi,
Quick questions regarding MAGPIO setup.
We are setting up MAGPIO pins via AT commands for RF switches.
Should the AT sentence for setting up MAGPIO be the same...
For a customer we're trying to see if we can build an IoT solution with nrf9160 to periodically send a status update to the cloud. Unfortunately, the devices are typically...
Hi everyone,
I suppose that this is a simple question but I cannot figure out what I am doing wrong. I am trying to set up an interrupt for a GPIO
I call the createInterrupt...
Hi ,
I am working nrf9160 project. I am facing error while downloading the project.
I followed the ticket - https://devzone.nordicsemi.com/f/nordic-q-a/50422/how-send...
Hello together, I am trying to work with the SEGGER software and would like to test it with a Sample from the nRF Connect SDK.
I've installed it over the Toolchain application...
