Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I want to use the SoftDevice APIs to read and write flash on the nRF51822. Are there any examples of how to do this. I see all kinds of mixes between pstorage, NVIC (not sure...
Hello,
I am new to Nordic and quite new to ZigBee. Just had a short evaluation with Silabs so far.
My goal is developing a custom lamp for serial production that needs...
Hello,
I am trying to perform a FOTA update from nrfCloud to a Thiny:91 device, but I notice that a mansage appears forcing me to update to FOTA_V2. The problem is that...
Hi,
Are the functions implemented in drv_uart and uart_app even related to each other? I noticed that uart_app implements only some simple functions. Can someone please...
Good morning Now, using nRF52832, I want to implement multiple central devices (smartphones) with one peripheral device (nRF52832 Device) to simultaneously perform BLE Multi...
I'm trying to send ADC data through BLE using nRF52840.
According to the example codes named ble_peripheral/ble_app_uart , peripheral/saadc , I wrote a code and it is...
With SEGGER Embedded Studio 5.10d and nRF52840, the register view show TIMER0-2 with 6 CC registers but they only have 4.
It's quite confusing particularly when using the...
Hi everyone,
I have created a BLE connection utilizing E73-2G4M04S1B module from EBYTE with nRF52832 as its core.
My problem is its low range which is limited to 15meters...
I'm trying to figure out why my Xbee3 module can't connect to my nRF52480 app. I built the app using SDK 7.2.0 and Segger and it runs great. I can connect to it from nRF tools...
Hi,
I am using app_timer and SoftDevice in NRF52810.
I am storing app_timer_cnt_get() value after releasing button and after completing BLE Advertisment.
as I am starting...
Hey all,
I have started working with this board around a month ago, and start to understand it little by little. I have a program that communicates with a display over UART...
Attempting to program an nRF52840 dongle with sniffer_nrf52840dongle_nrf52840_7cc811f.hex, using nRF Connect Programmer v1.4.8, on Windows 7
Upon clicking "Write", the red...
HI,
I am trying to use STTS751-1DP3F temp. sensor with nr52832. The drivers for sensors are given on:
https://github.com/STMicroelectronics/STMems_Standard_C_drivers/tree...
I have some old production code that uses s110 v 5/6 and SDK 8.0.0 (perhaps - no one seems to know). The production device has never been able to do a bonded reconnect correctly...
Hi,
Your online power estimator only concerns nRF52840/832/810.
How to get a value when using nRF5233 with CTE activated for AoA ?
In other words, what is the additional...
