In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
Hi everyone!
I am trying to implement the OTA - DFU in my project. I have my own board with a nrF52832 chip.
The project was build using SDK 13.0.0 and softdevice s132...
Dear Nordic Support Team,
I was using the CoAP and MQTT components in nRF5 SDK v16.0 .
So my device was able to do CoAP and MQTT via BLE 6LoWPAN. Adding a BLE service...
I am following the turtorial in the Github and build a project which add a custom service. The project can read, write and notify between the board and mobile nRF connect...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board.
I am using the UART module and associated UART drivers.
Is there a way to ignore the...
I have two nRF9160 DK boards that are programmed with modem firmware version 1.1.1 and are using V1.2.0 sdk software. They also are both programmed with the same mqtt_simple...
Hello,
I want to to configure mesh proxy node and along with that it should also contain relay functionalities using nrf5_SDK_for_Mesh_v4.1.0_src.
Is there any sample...
I'm seeing some issues I don't understand when using RTT. Here is a short fragment of code around the RTT_Write statement.
The commented out statements are included while...
I am using nRFConnect with nRF52840 Dongle. Since the last update to SoftDeviceAPI v5, nRFConnect cannot connect anymore to this specific devices (cheap JDY-10 BT/Serial adapters...
Hi, I want to store some personal data through flash in the LPN mesh routine. I read some posts and can be implemented by using flash manager, but I can't find the relevant...
Hello, I am working on storing words to flash using fds. I am working with the nRF52 DK and SDK V15.2.0. As mentioned in my earlier post , I am storing some critical state...
Hi,
Greetings!
I am using below setup:
SDK: v16.0.0
Mesh SDK: v4.0.0
Application: Light switch server and client
Hardware: nRF52DK
Distance between client and...
Hi, I am using ble_app_uart example for peripheral device and it will be powered by a 3.7 V battery. I need to use battery as long as possible. So I decided to make peripheral...
When I put the device into sleep it draws app 30 uA in sleep mode. Read in the manual: "Core standby current= 50 μA", "Current drawn if HFXO is forced on through for instance...
Hi,
I am trying to emulate a vendor's tool, whose BLE properties are configured as follows: Custom 128 bit Service UUID like XXXXXXXX- 0000 -XXXX-XXXX-XXXXXXXXXXXX
Custom...