I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello I need a falling edge response via GPIOTE. The settings I use for sdk 16 to sdk 14.2.0 do not work. For sdk 16 I use the functions nrfx_gpiote _..., for sdk 14.2.0 nrf_drv_gpiote_...
I observed a peak of 334 ua during system-on low-power mode during idle time which is periodic around 4 sec. I am using ble with RC clock option.
1.is it waking for calibration...
Previously, I learned that BLE is capable of 1:1, 1:N, and N:N communication, but I didn't get the exact information. Can I get some information? How do you do it, what's...
What is the max current nRF52840-DK source from Vdd pins, i am connecting multiple sensors through the Vdd of nRF52840-DK i want to know how much load it can source ?
Hello,
There is a problem printing the log message. I am using SDK12.3, keil compiler and segger J-Link. After modifying the project a little, normal log output is not available...
Does the nRF9160 have an ATEX component certificate? Why there is no marking such as "Ex ia IIC Ga" provided? What exactly do you understand by the term "ATEX compliance"...
After a conversation with a Nordic engineer and some research it looks like there is no official way to upgrade a product over the air from an nRF5 SDK based product to an...
I ported the Thread Secure DFU example to use FreeRTOS, however I get a hard fault if something is scheduled using the app_timer provided.
Calling coap_dfu_trigger or handling...
We have a custom PCB fitted with the nRF52840 SOC, we've previously erased and written to it via the nRF programmer tool. However, when trying to use the nrfjprog -e command...
Hi. I am having trouble connecting nrf5340 PDK to nRF Connect app on my phone.
I am using the peripheral_uart example based on https://infocenter.nordicsemi.com/index.jsp...
My customer is using a Taiyo Yuden module, EYSLSNZWW, that uses the Nordic nRF52810 chipset. We need to configure the board for Bluetooth Qualification testing. I have read...
Hello,
I use the TP4056 charging module and the 3.7V lithium battery (300mAh) and work on sdk v17.
One of the features I'm trying to create is when the charging connector...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I am trying to test ble_app_blinky_c.
I have problem with received data from peripheral which is my...
Hi,
I am new to the nrf52832 and I wanted to use its Bluetooth functionality for a project I am working on. I have read about the theory behind the Bluetooth stack etc,...
Hi,
Is there any sample Android mobile application available which calls or consume the Temperature/humidity for nrf5_SDK_for_Mesh_v3.2.0 ?
Best Regards,
