Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello,
Does anyone has an example of MQTT LST application for nrf9160.
I've tried to use the MQTT_Simple sample with LST.
I've add "CONFIG_MQTT_LIB_TLS =y" change the...
Hi everyone,
I am designing my own PCB using Raytac's module MDBT50Q-1MV2 that carries on the nRF52840 SOC.
The system will operate in normal voltage mode (VDD = VDDH...
Dear All,
I am trying to compile a project from the command line and I want to enable all the warnings possible for the files that I have created. I am using the NCS v1...
hi support team,
i tested the example of \\nRF5_SDK_16\examples\peripheral\usbd_msc , and SD card interface , that with the APP_SDCARD_FREQ_INIT 268435456 (1 M) and APP_SDCARD_FREQ_DATA...
Hi DevZone,
I created my project on SES in order to download files from a web server. So I decided to include in my project the "download_client" library which contains...
Hello! I am working on updating from SDK 15.2.0 to the SDK 16.0.0 and have encountered some problems when trying to use DFU OTA to flash my unit with the application.
I...
I need to be able to measure the battery level of the NRF52 with the internal ADC.
I know it can be done, but I don't really know how to configure it
I am using MBED...
I have purchased an nRF51822 module. I am using the Arduino IDE and the ST link to program the module. I have used the library BLEPeripheral by Sandeep Mistry (see below)...
I deleted a node in the mesh app without unprovisioning the node. I then reprogrammed the dongle hoping that everything will be reset. It seems the dongle is still provisioned...
I am following the example given in the SDK v16 with nRF52832/ nRF52840. For the given example UART is working fine. But whenever I am changing the default pin configuration...
Hello,
We are working on the NRF52840 with the SDK15.3 and the softdevice 6.1.1, we are trying to connect to different mobile centrals via ble. We are facing problems...
Hello,
We are trying to develop a gateway (central) to interface with off the shelf BLE devices. One of the functions of the device is to send logged data to the client...
Hi - I am trying to create a CLI project with FreeRTOS , the project will be used as an aggregator .
I can not figure out why I can't enable CLI , code hangs. would appriciate...
