I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
New to using EGU, trying to use it to implement software interrupts. How do I capture an Event?
I can see how to trigger and clear an event using -
nrf_egu_task_trigger...
In the function ble_init, I am getting an undefined reference to sd_softdevice_enable during the linking process. I see that in nrf_sdm.h there is SVCALL(SD_SOFTDEVICE_ENABLE...
Hello,
I am looking for the cost effective simultaneous central+peripheral solution using nrf BLE.
The nrf52810 seems to be hardware capable of doing this but I am...
Hi, I am creating custom ble service.there i need to perform
1. character - READ , NOTIF
2. character - WRITE READ
3 . character - READ,WRITE, NOTIF
I achieved ...
Hi
I'm on a custom board with NCS 1.2.0 and modem firmware 1.2.0.
We have implemented agps, and testing with 2 units with agps colocated with 1 unit without agps. All...
Strange device crash on deprovisioning.
This is probably something incredibly stupid, but I have been fighting this problem for a week and don't know where to turn.
I...
Hello
I program the example code peripheral " ble_app_hrs -pca10040e -s112" on nRF52810 and central " ble_app_hrs_c-pca10040 -s132" on nRF52832 .
I used nRF Toolbox on...
Hi,
we are working with Nrf52 and do not need/use Bluetooth, i.e. our devices will not have the Softdevice stack installed.
I was informed that for the radio certification...
Hello, I am using nRF52840, SDK 16, SoftDevice s140 with SES. I want to configure my device first in connectable mode and then in non-connectable beacon mode. sys_advertising_init...
Hi,
The situation is very simple; I try to use the CoAP Utils library to simplify CoAP usage in an application running on the nRF9160 DK ( https://developer.nordicsemi...
Hello,
I’m using the ble_app_multirole_lesc application from SDK 16.0.0_98a08e2 as is (not modified) on 2 PCA10040 dev kits but unfortunetly both boards return a disconnection...
hi, nordic support
SDK version is 15.3.0
the example is ble_app_uart_c
I have modified the project based on this address： https://infocenter.nordicsemi.com/index.jsp...
Using nRF Connect SDK v2.1.0 and the nRF5340 PDK, are any of the ble mesh samples in the fw-nrfconnect-nrf repo working yet? I've tried both the mesh light and light_switch...
