Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
I plan to connect an nRF52810 bluetooth output to a Johansen Tech 2450AT07A0100 chip antenna via a Johansen 2450FM07A0029 impedance matching chip. Do you have a BT SIG approved...
Hi, I am using nRf9160 with last sdk (master branch) and Segger Embedded studio V4.52. When I compile and run any program everything works, but when I try to debug the program...
Hi community ! Imagine this configuration :
A -> B -> C
So A can't directly communicate with C. I send a message from A to C (And only C), so this one with be relayed...
Hi,
I am working on project which is based on nrf9160. I added the source files and user define header files . and also given the path of source file in CMake file. Build...
Is it possible to configure the Zephyr UART parameters like the hardware flow control dynamically at run time? We do that in an nRF52840 firmware with the nrfx libraries ...
Hi all:
Our usage scenario is to establish a connection and bonded between the NRF52840 peripheral device and the central device, and then restart the NRF52840 peripheral...
Hello,
I was working on a project SDK=16.0, SD=7.0.1, device=nRF52811.
After making a few changes to a working code which I compiled successfully many times before and...
Hello!
I am experienced in using mbedTLS on other platforms, and am in the process of porting my implementation of COSE (RFC 8512) to the Nordic SDK.
As a starting point...
HI NORDIC, I met a problem that Bootloader coulde jump to application, and the application crashed with freertos and softdevice SDK13.0. However the application could run...
After reprogramming with mfw_nrf9160_1.2.0 and nrf9160dk_asset_tracker_ltem_2020-04-29_bc7ade8b.hex
the nRF9160 fails to connect properly. LED3 blinks continually, LED4...
Hello,
currently i am using nRF52832 board with Nordic SDK 16.0.0 and softdevice version 7.0.1
i have separated DFU service and bootloader code. added dfu service in my...
Hello all,
I'm still learning C at this point of stage. What I ended up was following a tutorial online on simple BLE project controlling the on-board LED.
The tutorial...
This is a 2 part question concerning the LFCLK input levels as well as how to test the LFCLK frequency against the HFCLK frequency to make sure they are consistent.
In this...
I am currently working on a project using the MAX30102 Heart rate module. This sensor has red & ir led's. I connected the the max30102 sensor to the nrf52 DK as follows VDD...
