I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear Nordic Team!
I am verifying my tools chain for nrf52840 Mesh project development by mesh light-switch example. I have 4 PCA10056 and make them to 1 provisioner, 1 client...
Hi,
I use sdk16 and nRF52832.I want to change advertising in the air:
Now I'm using the timer to change the adv.But I want to change adv with RF interrupt.
Like this...
I developed an application (BLE named Adriano) using nRF52840 DK, nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730, starting from ble_zigbee_dynamic example. I added some custom...
Hi,
I'm developping an application for nRF52840 as a BLE central. It is supposed to connect to an Android device (BLE peripheral) using a bond (encrypted connection with...
Hi everyone,
I went through the source code by Vidar Berg for background dfu using SDK 15.3. I am working with nRF52832 , S132 and SDk 12 with Keil IDE. I did try with secure...
Hi,
I am currently developing with nRF52811 chip using nRF52840 DK. Where can I find a reference 2.4GHz PCB antenna design document?
Thanks.
Regards,
Jxq
Dear Team:
Hi team,I just want to know:
1.Can the ESB protocol call the frequency hopping of Gazell? Is there a corresponding description and source code?
2.Can the...
hi, i am facing this unknown error at "unknown function at 0x000008C8",
i am doing a development project with nrf52832(sdk14.2 and s132v5,ble nus is used) mcu and sim800...
Hello, I'm developing SAADC on nRF52832.
While developing, I have problems now.
I applied sine wave on ADC input.
And the result is displayed on the figure that I...
Hi:
Use the nordic official nRF52832 development board , The software is SDK15.3(example: ble_app_uart ),
Find that there will be a continuous reset. What is the problem...
Hey all,
I am trying to run the "nrfx_spim" example on my nRF52840 USB Dongle (Makerdiary nRF52840 USB dongle), however it is not working. It looks like the code is never...
I have been testing the softdevice codes on NRF52840 DK with NRF52840 SDK 15.2.0 which is working perfectly. But when i put the same test code in our custom board having BT840...
Hello,
I'm still trying to deal with the CLI-coordinator and I have a problem. I am using nRF52840 chip and SDK 4.0.0.
I just can’t understand how I can find out from...
Hi,
I ported an nrf example from nRF5 SDK version 12.3.0 ble_proximity to segger studio (v4.50), and flashed into nRF51DK, using build and run option. The application is...
Hi I've been trying to get started with the nrf52840 dk and dongle on my Windows 10 machine but have been stuck on this set-up issue. I'm using the following versions:
...
