Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello Nordic
I am working with nrf52832, sdk 16.0, softdevice s132
I need to advertise NON CONNECTABLE ble with changeable data (later relevant data will be received...
Hi
we are using the nRF52840 and antenna signal i connected ceramic chip antenna(ACAG020-2450-T).
The above attached schematic of ant signal matching circuit schematic...
The only way I can see to do it is by two separate PPI calls. So Timer1 "tasker" is firing both the capture and clear... but will they execute sequentially?
Hi,
I just bought the NRF52850 DK. Currently I do not have the JLink connector to perform debugging using UART.
Is there is a way I can print printf or NRF LOG through...
Hello expert,
I would like to design a custom PCB that has two transceivers on it. One transceiver is working as a beacon/continuous wave generator (TX) and the other one...
On the basis of NRF24L01 +, an antenna was designed. after designing, I need to carry out the coordination of circuits. Do not tell me how best to do this, what values to...
I had a setup where I could DFU OTA a NRF52832 based board
I moved to a NRF52840 based board and now during the OTA DFU I get messages like this
I did try a new bootloader...
Hello, guys.
We have nRF9160DK and nRF Connect SDK v1.3.0. The version of the LTE modem firmware is the latest (v.1.2.0).
In our design, we are able to initially connect...
Hi Nordic team,
I just purchased a row of new nrf9160 SiPs for our IoT products. We are testing with new made cuicuits.
We use the same circuit schematic that worked with...
Hello,
Problem: BLE doesn't work on a OurBoard with nRF52840 (Schema1).
1) BLE example is working DevBoard (can see BLE server by scanner). On the OurBoard the examle...
Hello,
I've been testing HCI_UART from Zephyr RTOS on nRF52840DK and own device which has nRF52840 + FT232R as USB-UART converter. Regarding the own device it's a circuit...
I am studying the beacon example provided in the SDK (The project is found in following directory C:\Nordic_semi\nRF5SDK160098a08e2\examples\ble_peripheral\ble_app_beacon...
Hello there, I'm developing a device who will use two NRF52832(ANNA-B112 Module). They will communicate as central and peripheral. But i'm facing a problem, i need to after...
I could decrease current consumption at v1.2.0, but couldn't at 1.3.0. 520uA flows in k_cpu_idle();
How can you do that?
Also, in v1.3.0, CONFIG_UART_0_NRF_UARTE is depricated...
