I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Hi, I would like to run an nrf53 example project. I got the devkit, and after some struggle I am now able to compile and run a project.
I need to run an Bluetooth example...
This is really a question about best practice - I have some ideas of ways to do what I want, but wonder if there is some clean API-supported method that I haven't found.....
Hi, I am in design stage and i need to change nrf 8001 to nrf 52810. In this point i have a question about pin configuration in nrf52810, Can i use any pin for any use? i...
Hello everyone.
I know from Errata document that the GPS antenna soldered on DK is not working properly on the 0.8.2 version of the DK. I need to use GPS for time syncronization...
Hello,
We are allocating a large amount of pages (100 pages, ~400kB) for the Flash Data Storage module in order to hold collected data. As a result, the fds garbage collection...
Hi all, can the nRF52840 dongle be used as an external Bluetooth 5.0 peripheral via a Raspberry Pi 3 running Linux?
I received this message from my engineer
' The drivers...
This is based on the article fround in devzone here .
I'm compiling a simple Hello World and followed the instructions as per the nrf Connect SDK Turorial Part 2 .
To...
Howdy,
I'm using Zephyr to configure an nRF52840 to act as an I2C master and send data to a TM4C slave at a 100kHz clock rate. The nRF52840 appears to hang after calling...
Hello, I am working with nRF5 SDK 17.0.0 and using IAR Embedded Workbench 8.50.1. I am following the Secure DFU bootloader guide as posted here .
On Step B3, I get a build...
During development, it is a very common task to combine the 4 elements into a single hex file, softdevice, bootsettings, bootloader and application. Mergehex is limited to...
I'm using an nRF52840-Preview-DK board in a POC (Proof Of Concept) to convert an I2S-TDM bus to SPI.
So it takes the I2S FS (frame sync) and CLK (clock) signals as inputs...
Hi Team,
we are working on nrf52 and we doing encryption of the data.
on the receiver end I can understand if there is connection , the keys will be exchanged and after...
Part - NRF52810-QFAA-R7 Hi, I've tried two chips, reflowed and checked under microscope. I have a connection to the track the pin connects to. Errata is applied via SystemInit...
Hello Devzone,
Here is my issue : I want to have a low power mesh node that can just send message to other nodes. The device can enable and disable himself the mesh stack...
Hi
I'm following the procedure in this link https://openthread.io/guides/border-router/external-commissioning
I'd like eui and cc from the source code in the nrf52840dk...
