Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Do we have any examples of using tcp in non blocking mode for the NRF9160. I used the USP for PSM example as base for my current project but the blocking call seems to lead...
Hi,
I found some thing not seems to be right in SDK 16. I wonder if this is intentional or a bug. Bluetooth 5 max MTU can be up to 512 bytes. I found the definitions in...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have a use case where peripheral need...
The documentation for ERASEPROTECT.DISABLE states:
The erase protection mechanism can be disabled in order to return a device to factory default settings upon next reset...
Hi All,
I am using nRF52840 chip in one of my battery powered design. As I could see the datasheet and power calculator says the current consumption of nRF is less in...
Sir i am following this link -> https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.iotsdk.v0.9.0%2Fiot_sdk_app_mqtt_publisher.html
and I have one...
Hi! I'm using the fatfs library to read/write data from/to an SD-card. I noticed the following behaviour:
When I try to write or read data directly after receiving a BLE...
Hi All,
I am using nRF52840 in one of our design. As the P0.18 is the RESET pin, it is tough to route the trace without a pad on via. Hence as I have modified my design...
Hi Friend,
My platform is SDK 16 with S140 softdevice.
I set a gpio for edge trigger interrupt. But I cannot get the correct gpio state if the data pulse is too short...
Hello,
I want to test bluetooth on nRF9160DK. How to do that? I programmed nRF52 on nRF9160DK with hci uart sample and board selected is nrf52840_pca10090.
But how to...
I'm currently trying to add SUPL support to our existing product, and I'm finding that the SUPL library is absolutely huge. Enabling CONFIG_SUPL_CLIENT_LIB appears to add...
Was wondering if anyone knew why this fault might be triggered?
It triggers when I try to use SPI0 and LTE together.
AT host is disabled.
The code stops here during...
While trying to utilize the TEMP peripheral today, I found that after the event handler returns a single reading the application does not continue to run. Any actions that...
Hi,
I got the nRF connect sdk downloaded and I can build zephyr projects for the nrf5340_dk_nrf5340. I somehow fail t find the sample projects as mention in
https:/...
Hi all,
I have a question regarding the difference between the nRF51822XX AC and nRF51822XX AA during the configuration of IROM and IRAM in Keil software.
I know that...
