I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Sorry to bring up a topic which seems to have been discussed already, but I don't see an answer to my specific questions.
The original design of my project was to have both...
Hi,
The known issues section of SDK v1.3.0 release note states that
"
nRF5340
FOTA with the SMP Server Sample does not work.
"
Is this fixed in version 1.3.1?
Good morning, I'm working with the nRF52 DK and a custom board that has the nRF52810.
I am using the SDK 15.0.0 and followed the tutorial described here:
https://devzone...
Do you think my nrf is original?
The person I bought says it's original.
Can you please check it?
Seller link: http://www.ebyte.com/en/product-view-news.aspx?id=113
Hi,
I have a custom board in which i am using nRF52840 with SDK version is 16.0.0.
I have tested app_uart library its working Ok and current consumption is 6 uA in deep...
Hello,
I'm developing a project which uses two threads. One configures UART and keeps on a while(1) loop. But once it receives a byte, an ISR pushes the incoming byte...
Hello
I am adding the mpu6050 library in the ble_app_template of SDK 14.2.
Use the ble_mpu6050_simple example here. https://github.com/Martinsbl/nrf5-mpu-examples
I...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi everyone,
Looking the examples of SDK16, I noticed that every example has a hex folder with some .hex files inside . This applies for both peripheral and ble examples...
Hello,
I want flash NRF52840 using AM57xx sitara processor(running on linux) over SWD interface. Can you please provide steps for the same. Is there any other methods available...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice. We are able to perform a DFU by downloading the .bin and .dat files of the new firmware in...
Hi,
Following the example https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/thread_example_dfu.html how can you connect a jlink debugger and step through the application...
I read here...
NRF52840_PS_v1.1.pdf Peripherals > UART (6.33.7)
“An ERROR event, in the form of a framing error, will be generated if a valid stop bit is not detected...
Hi,
is there an updated example for SDK 15 or 17 for the multiprotocol example which uses BLE and ESB via the timeslot concurrently and at the same time allows the normal...
Hi ,
i am new to using SPI and i am currently undergoing my final year porject that consits of data analyisis for IMUs and i am uding the nrf52DK (which i never used before...
