Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi everyone. I'm trying to add UART Service to Mesh light switch example in Mesh SDK latest version 1.0.1. Is it possible? And When Nordic will provide integrated Mesh SDK...
Hello everyone,
I am currently working on a project, where I want to interface UART to a Bluetooth mesh network. The project is very similar to the light switch demo, because...
Hi Team,
I am working on Mesh SDK 3.10, I have requirement of mesh with Ble Uart. So I decide to take this example "ble_app_uart_coesixt". I build this example without...
Good day, support!
I have a couple of questions regarding the firmware of the nRF52840 dongle.
1) How to identify the firmware version that is nRF Connect flashing ...
After following the " Using a custom Secure Partition Manager with your application " Guide for the nRF5340-PDK, I experienced following error:
I tried to create a Non-Secure...
Hello every one.
I am new with Segger and nRF52.
I tried to create my own library for OB1203 sensor.
But i stack here when Segger view this error: Below is my screen...
As we are performing climate tests for custom PCB based on Nordic nrf52832 SOC, in low temperature i.e -20 Deg C the communication is not stable. After verifying the HFCLKSTAT...
Hi,
We thought to have a setup like this
1<-->2<-->3
1 is MESH ADV device with some mesh model
2 is MESH ADV + regular BLE stack support
3 is Gateway with...
I am trying to collect sensor data and store in flash using qspi interface. Unlike the peripheral example code, the qspi data handler function is not getting hit with ble...
Hello, I have another problem... i work on nrf9160 dk
I try to send http post when i pressed button 2 but this doesn't work.. Below you could see my code who block on printk...
I have been reviewing this merge: https://github.com/NordicPlayground/fw-nrfconnect-nrf/pull/1982 and it appears that there is capability in the fota example to enable https...
How to configure the start address and size of flash memory and nrf52832 in SES and how to calculate the size? How to calculate the start address and size of app and bootloader...
Hi,
Current Status:
I'm trying to run the fpu_fft example from the SDK 15.3.0 on my nRF52832 DevKit. When I clean and build the project in SES everything is fine and I...
Hi, I have a question about unknown flash data from MBR area which start from offset 0x0000035C, 20 bytes data show as below.
Data[20] : FF FF FF FF FF FF FF FF FF FF FF...
