Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello,
Would appreciate some understanding of a compiler warning. Developing for nRF52832 using SDK 15.3.0 plus S112.
This code compiles without warning:
Then I switch...
I have tried a lot of different settings but the NRF52810 still does not output carrier..
How do I configure the radio to only send carrier for NRF52810?
Hi,
I need to stream data from NUS UART Central Device to one peripheral, but the device always disconnects while trying to send second set of data. So I changed the write_req...
Dear
I have changed light_switch server example of " nrf5_SDK_for_Mesh_v4.0.0_src" from PCA10056 to PCA10059. All function of the code works well except button.
For button...
Morning. I have a Fanstel840F module. I use attached example sketch. I flash nrf52DK with this sketch, it works fine. I can scan with NRF PC and Mobile software, and see smartTag1003...
Hi,
May i know any software utility suggestion to debug the USB data (200 bytes data) communication from device to host and vice versa for nRF52840.
Similar USB sniffer...
I think there is a bug in the west tool. If only one -Dxxxx=”xx.h" parameter in the command-line, the quotes will be filtered. So update the "nrfxlib\nrf_security\src\mbedtls...
Hello, everyone!
I am using nRF52DK and SDK v17, and I am dealing with the example of ble_app_uart.
Using this example, I am testing how buttons control BLE scanning...
Hello. I am trying to implement a application jump from my normal firmware located at memory 0x19000 per recommendations based on the soft device used (s112) to a different...
Hello,
I am working on the nrf9160 board using cloud client sample. The connection to AWS and the boards loses after running for a while. When I reset the board it connects...
Hi,
I'm super rookie on BLE project,
my question is how can I using button press to accept a central pairing instead of typing passkey,
here's my code, using nrf 52810...
Hello!
We are trying to send MQTT messages to a hosted mosquito broker via AT commands using the nRF9160.
We are trying to avoid programming the nrf9160 chip, as we...
SAADC resolution is set to 8 bits, channel is configured as single ended. Is it correct to say that SAADC digital output should be between 0x0000 and 0x00FF(full scale)? ...
Hi,
I'm testing the ble_app_uart example on the nRF52840 DK and it seems to be consuming a lot of current similar to the case in https://devzone.nordicsemi.com/f/nordic...
In a single core BLE SOC, whenever a BLE event occurs the BLE stack takes high priority and any application code running on the single core, is delayed while the event is...
