Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hello Everyone,
I am using nrf52832 and sdk 15.2 for ota over serial. I have made bootloader for OTA over UART and tested same with nrfutil using my dfu package file. firmware...
Hi. I my embedded code I read default MAC address internally and mine is read as 73:7F:..... but in reality is supposed to be F3:7F.....
I have read few tickets where people...
Hello,
We are designing a custom board, and we would like to use an external crystal for the low frequency clock source, but we are running into disconnect issues. A similar...
Hi,
I have been trying to get the BLE secure DFU example working on a custom board (nrf52840 - BC840 module). I tried it on SDK 15 and SDK 16. When I flash the BLE DFU,...
I am trying to get the current time and the current time zone. I see there is some modem commands LWM2M commands that appear to have the capability to do that. When I try...
Dear all,
I have an application that requires me to keep advertising until the button is pressed.
I use a timer to read the status of the input pin and then if input is...
All of our initial BLE project development has been done using a the Nordic nRF5_SDK_15.3.0_59ac345 SDK and 10056 eval board. Now we have a production board that is based...
Hi All,
I am developing an application with a custom BLE profile, one in which i would like to notify the central of certain values as soon as they connect. I have built...
Dear Devzone team,
What is the fasted way to fetch and store the Thingy91 measurement and device data outside of the nrf Cloud? If i just deploy the AWS certificates will...
Hello,
We are currently working on a project where up to 40 battery powered devices need to talk with one router/coordinator. Each device features a proximity sensor and...
The instructions do not tally with https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v12.2.0%2Flib_crypto.html&cp=4_0_1_3_9_2&anchor=lib_crypto_installing...
Hello everybody,
I tried to send data while in scanning mode (RX 100%).
I don't get any error when sending but data seems not to be sent (not shown in ANTWARE).
Is what...
Hi
So, Im trying to repeat the ble_central_and_peripheral example but with my own services. To be easier let's call the service " snsr ". So, I did the snsr.c and the snsr_c...
We have a situation where a device might have a sim card field installed, and sometimes, depending on the vendor, the APN settings might need to get changed.
Is there a...
