Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi, We were trying with a new n/w carrier in Canada ( Maxim ). nrf9160 is able to connect to the network, but it is not able to resolve our server URL ipv4 address. Below...
Hi,
I am testing RX mode.
And the module is sure to enable M1 (%XSYSTEMMODE: 1,0,0,0)
I use the following command, but return error.
AT%XRFTEST=1,1,2,19500,17,1,0...
Hello,
I´m writing my thesis and using the Online Power Profiler to get a estimation about current consumption in NB-IoT cases.
I would like to use the diagram from the...
Hi, I have developed zigbee stack.
I tested to connect the door lock example of Thread and Zigbee SDK 3.2.0 with ZC of SDK 4.2.0.
I checked connection with these.
So...
Hi,
We are going to use NRF52832 for a project, and planning to design our own PCB card and assemble the NRF52832 chips, purchased through Digikey or a similar distributor...
Hi everyone,
I have designed a project based on the Radio test example, in the Nordic SDK. After programming all my code on the NRF52833 DK (PCA10100), i decided to design...
Hello, I have 4 NRF51822 modules, 2 stlink programmers, and a BLE400 board, I was using the same module with the same stlink each time, but the led on the board stopped lighting...
Hi,
I am going to transmit and receive data with libuarte. I read the libuarte example, but I am not quite sure my understanding of the data transfer process is correct...
Hello
I am trying to configure the spis with the nrfx drivers. My code is as follows:
I enabled the nrfx SPIS driver and the nrfx SPIS3 instance via Segger Embedded...
Dear,
I want copy antenna design from PCA10040 for BLE. Could you please help to provide antenna's spec, such as gain, efficiency, Radiation Pattern?
Thank you.
We are trying to program the nRF5340 via SWD from a host MCU and would like to understand if there is a white paper/blog post similar to this one:
https://devzone.nordicsemi...
Hi, Currently, we work on a project that uses: nRF9160 Zyphre OS Segger Embedded Studio for Arm (Nordic Edition) V5.10d SDK v1.4
This is our situation.
We want to measure...
A few things to preface:
Hardware: nRF52840 Development Kit (PCA10056 - 2.0.1 - 2020.11)
Nordic SDK: nRF5_SDK_17.0.0_9d13099
Central example project I am using: nRF5_SDK_17...
Hi,
How do we get the GPS speed accuracy out of the module? We have used other GPS modules in the past which have output the speed accuracy which we use to qualify the data...
