We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
We are using NRF52840 Dk board to transfer the data at 10ms through Bluetooth which is central and peripheral as other cc250moda controller Bluetooth. Our objective...
Hello:
I am porting the LESC with MITM security protocol from your "ble_app_multirole_lesc" example inyo a project that runs FreeRTOS. This is on an NRF32540 With s140...
Hi,
I'm using an nrf52840 dk to query another device over spi and then pipe the response back USB to a host PC. Ideally, we're piping data at 1 Mbps (which should be very...
Hi,
We are using nRF9160 DK. Loaded the asset tracking application, and followed all the procedure to connect to nRF cloud.
In nRF cloud i can see the data in the cloud...
Hello,
I am currently designing a custom PCB with the nRF8001 chip. For a smoother assembly and component procurement, I am looking to make all the resistors on the board...
Hi there,
I have a problem with the bootloader from the RF5_SDK_11.0.0_89a8197 together with Intel Wireless Bluetooth chipset.
I use the softdevice s132_nrf52_2.0..1. I have...
Hi im after the library driver for the nRF509 using Arduino but when i go to the webpage to get it the webpage says not available can someone advise please
Many thanks ...
Hello,
Is it correct, that periodic advertising is working only with non-connectable mode? To implement periodic advertising with connected mode I need to start the second...
Hi, I tested a simple client-server UDP application, using as a template the UDP examples from the SDK. The UDP server is running in a nRF52 board and the client is a Python...
Hi,
my goal is to send data to the Google Cloud Platform using CoAP.
I found this example:
https://infocenter.nordicsemi.com/topic/sdk_tz_v3.1.0/thread_google_iot_coap...
Hi,
Recently I have been working on nrf9160 and wanted it to work as a modem for a linux computer for example raspberry pi. The aim here is that I connect the nrf9160 to...
Hi,
We are using nRF9160 DK. On the Arduino connector, we connected STM X-Nucleo-IKS01A2 sensor shield. We wanted to fetch the sensor values using nRF9160.
What example...
Dear Sirs, good night
Currently developing hardware using nRF52840 based module (BT840X from Fanstel)
Wanted to ask if following assignment would be OK for controlling...
I would like to know What is the limit on the number of ble devices that can be tracked concurrently by one Nrf52833 acting as an AoA device?.
Is there any reference antenna...
