Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I am using custom board nRF52820. I'd done OTA up-gradation with USB connected. Firmware successfully updated on device over BLE and device got soft reset.
After removal...
I am using nRF9160 DK(PCA10090 0.9.0 2019.19) with Indian carrier LTE-M SIM and carried below steps to establish LTE-M communication with nRF Cloud: 1. Upgraded to latest...
Dear community,
I opened and successfully tried out the preflash_example. Since I will need a plain text NDEF message instead of an URI NDEF message as used in the example...
Hello,
I'm new to BLE and have a general question about concurrency and collisions. Sorry if a repeat question. I'm developing for nRF52832 using SDK 15.3 and S112 v6.1...
Hello,
I am testing nRF52 UART with DSP.
While transmit data in nRF52 (ADC results)
(example link: https://github.com/NordicPlayground/nRF52-ADC-examples )
I can show...
Hi
I am now working on a project which I use ble_app_uart_c as a reference.
SDK 16 and used softdevice s140.
The radio_tx_carrier() function was taken from example/peripheral...
So I bought a BLE Heart Rate Sensor (chest strap) from market. I am able to read data using the nRF Connect Android App. Now I am trying to read the Heart rate data using...
Hello,
I'm working with PCA10040 EVB.
I've followed this FAQ that shows how to add a device name.
But function sd_ble_gap_adv_set_configure() (called at the end of advertising_init...
Hi,
Forgive what may seem like a stupid question, but...
I would like to create a first reference PCB design using an nRF52832 for an IoT project I am working on.
I...
Hello,
For the function to acquire the FDS file system status, I noticed that the struct member variables are held in uint16_t. Some values, such as words_used and freeable_words...
nRF42840DK, SES V4.52c:
Project was copied from 17.0.0 to 17.0.2 and link now fails:
Building 'ble_app_att_mtu_throughput_pca10056_s140' from solution 'ble_app_att_mtu_throughput_pca10056_s140...
I have been trying to find some help or an example of using a capacitive sense button with the csense library(in SAADC mode) but also read the voltage of my battery using...
The Mac version of nRF Connect shows the Device Information Service characteristic Serial Number String as hex, not a string. It shows properly as a string on the iOS version...
Hi,
I'm changing the peripheral device name by sending a command from the host over ble. I can see the changed device name after the host disconnects. Is it possible to...
Given the info here and here ...
1. Does this mean that the nordic example here is wrong, and that line 54 should be time_struct. tm_mon = month - 1; to account for the...
