But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hi i'm studying ESB in nrf52833 DK
I have a few question.
1. When a packet is sent from ptx to prx, transaction starts, and when prx receives a packet from ptx, it sends...
Hi,
I want to add ble dfu to the hid keyboard example using nRF52810. I have tried unbonded and bonded，both are not work.
By using the bonded way, I made the following...
HI,ALL:
In SDK16, 1 .as topic,when I trigger the mouse_movement_send() and the mouse_click_send() at the same time, Error occurs.
2.how to detect BLE search device sucessfully...
Dear Members,
I tried to find a file *pca10056 project for bsc_rx on ant_plus ?
Can anyone tell me where I can find that file on the SDK ?
Thanks
Visit my lab...
We use a frontend that requires four pins and the timeslot API with our own protocol on nRF52832 & nRF52840. This works fine, but for BLE to work properly we need to leave...
i have a problem with the nRF52 DK (PCA10040) I followed these instructions https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3.1.pdf and the python version is 3.9...
Hi, I am using nRF Connect SDK 14.0 with nRF9160 DK.
I want to use nRF52840 as a controller and nRF9160 as host. To achieve this, I flashed hci_uart sample on nRF52840 and...
Hello!
I move my device from nRF52811 to nRF52820 ( QDAA-C00 ) and I have a problem when using a comparator and TWI
If I configure TWI0 or TWI1 and use it with external...
Good day,
I am using a DK board with the nRF52832 (pca10040) and I am using a 4 kHz buzzer connected to the gpio 16. I have seen the examples pwm_driver and pwm_library...
Hi, I am using the Nordic nRF52832, with the Segger IDE（Nordic）, and v1.4.0 of theSDK, and would like to know how to enable both LLPM and Multilink.
I am starting from the...
Hi.
I want to ask about the Queued Writes module and the NRF_SDH_BLE_VS_UUID_COUNT. In the example ble_app_uart, in the "services_init(void)" function we initialize the...
Hi,
I'm having difficulties running the secure bootloader example (ble_debug version), it doesn't seem to be advertising or providing any logs.
I'm currently using the...
Hi,
I want to create a fresh project in Keil with nRF SDK as static library included into application. I have created the project, but when I run, the code always stuck...
Hi,
The error I get is as followed:
Output/Debug/Exe/Lesson10_Part3.elf section `.nrf_balloc' will not fit in region `UNPLACED_SECTIONS'
region `UNPLACED_SECTIONS' overflowed...
