But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
I use SES for debugging,
the chip is nrf52840 with softdevice 140, sdk 15.3
I ported a project from 2017 and now I'm ready to compile all without any error,
but as...
I try to build and debugg a programm from 2017: SDK15.3 Sofdevice 140 5.0.0.2 alpha plattform was eclipse neon
I switched the plattform to SES because neon sucks too install...
Hello,
We have a custom device using nRF52832 with a MTU of 20 bytes, and for one of the tests we are trying to write 248 bytes to the device with nRFConnect, can the "add...
Hi
I want to download the reference design of NRF52840 develop board, I found the follow address ...
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I've add gps with supl in a project, as in gps project.
If I try to use only gps, everythinks works, but when I put CONFIG_BSD_LIBRARY_TRACE_ENABLED to true, the...
Hi I am able to choose the nrf 52840 dongle in NRF Connect . However, compared to nrf 52840 DK , I am able to read then save as file/ erase & write / erase all.
With this...
Hello
my setup is s140, nrf52840. it is flashed the open bootloader(usb-serial) , the softdevice and an application and everything works fine, flashing running and updating...
hello nordic
i am working with nrf52832, with sdk 16.0 and s132 softdevice, tough i belive this question is relevant to all anrf52
i work with the twi driver (for i2c...
Hi every one , i tries to call the generic_onoff_client_set function to send a message from the client to the server but this ain't working. Can someone please help me?
...
Dear Forum,
I am looking for an OAM vendor offering a small keypad / pinpad device running on an nRF52 SoC. Should be powered by a rechargeable battery and have mini USB...
Hello.
I want to use the nrf52840 as Bluetooth radio controller which is connected over UART to Linux based ARM host.
We are targetting to use meshctl on linux host...
Hi ,
We are facing a problem with cellular connection in NB-IOT mode on NRF9160. We are trying with the asset tracker sample , but cellular connection does not happen. Can...
Hello Everyone,
I started to use the NRF52832 recently and wanted to use it with a sensor from Melexis called MLX90632. I am using sdk 15.0.0.
This sensor have a library...
Hello,
Currently I would like to add a functionality to Bluetooth Low Energy App (BLE). I have a bluetooth slave device that require a specific sequence of sending string...
So, i have been trying to perform a DFU over serial using the method mentioned here by Hung Bui.
Here is a summary of what i did:
- build and flash mcuboot
- build and...
