I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I am using nRF52840 as a master to communicate with esp32. For esp32 i am using arduino ide and esp 32 slave library( available in library manager of arduino ide).
For nRF52840...
Hello,
I use nrf52832 with 65 kb RAM.
I can't understand why soft device takes about 30k RAM memory.
I see "reserved_ram" has 30k.
Can I change size for 20k for...
We're using the nRF52840 on a battery-powered device that requires very low power consumption, both in run mode and also in the Cortex-M4 sleep / deep sleep modes. We've recently...
Hi, I'm trying to enable the entropy driver so that sys_csrand_get() will stop returning "Entropy reseed error". Does anyone know why it's grayed out? I have tried enabling...
Hi,
I know it's a very common question, but I still haven't fully understood. There is nrf52832 on the peripheral side, there is ble dongle on the central side.
How does...
Hi,
I am trying to get a project to compile using the the segger studio. I have copied one of the example applications and converted it according to your instruction here...
Hello,
I want to add a new driver directly in my project (out of tree), so I've add the differents files, as in the picture below.
When I compile, I get each time...
HI
I used NRF24L01 module in direct mode and chose 250kbps in configuration
In TX mode : whether the data from MCU to module has to be send through exact 250kbps?
Dear Sir
I am trying to work with the ADC .
Attached a code
I get the lines
00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772...
Hi Nordic Team,
Some time facing Connection issue in Mobile app and some time device advertisement is not getting in app.
I am using below chipset and configuration. ...
Dear all, I try to self provision device by it self following steps below: Step 1 : Bind key Step 2 : Subscribe to topic
Step3 : Set publication topic
Step 4 The main...
I am having issues running GPS and LTE concurrently on the nRF9160DK and am wondering if the rootcause is an incompatibility between modem FW v1.2 and hardware v0.9.0. I am...
Hello,
With regards to the HID Keyboard Example,
1) Is it posible to disconnect from the central side (ios)? I would like to be able to disconnect as follows:
But...
Hi,
I have just started using the Nordic SDK (nRF5_SDK_15.2.0_9412b96) and am developing a low power application for a custom PCB using the rf52840.
I am developing...
