Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Nordic's smart remote 3 is for nrf52832 and nrf52810.
I want to port the same on the nrf52840 DK.
I have basic IR receivers and Transmitter and want to integrate them...
I'm using the nrf52832 from fanstel (bt832) to stream audio to the adau1701 dsp. I want to be able to play music over Bluetooth. I'm using i2s to transfer the data to the...
Hello,
I am trying to change PHY after packet sent/received (known as asymmetric PHY).
After receiving EVENT_END, i write to register MODE to change the PHY.
This can...
Hi ,
I am using saadc to measure battery voltage i m using the sample example given as reference ble_app_proximity/
I am doing adc_configuration in one file and triggering...
Hello
I am starting with nRF 9160 DK and Segger Embedded Studio, I installed Segger through toolchain, the activation sim, updated of certificated and connect the DK to...
Hi everyone
Currently, I am working on a project related to the mesh network friendship feature on nrf52840. I am having the following problem: I have established a friendship...
I tried to debug UART communication between 52840 development board and 9160 development board. I sent 9 bytes of data from 52840 side, but I only received 8 bytes of data...
Hi,
I can't find how to get data received by interruption of UART. I've used libuarte example and I tried to get data from buffer buf in uart_event_handler, but it doesn...
I can see that other people have run into the "no code for breakpoint" problem when attempting to use the SEGGER debugger. I have read the earlier posts. I have not been able...
Dear Sir/Madam,
Can you please help to check and advise if both part# nRF52840-Dongle and nRF52840-DK have KC certificate? Thanks.
Best Regards,
Dan Lee
Hi,
I'm using for awhile TIMER0 and I want him completely disable.
I'm setting a TASKS STOP to stop a timer, clearing a interrupt and disabling interrupt in NVIC, but...
I'm looking at the datasheet for the NRF52832 because I'll be using it with a Raytac module and I'd like to know for sure how the SPI pins are set.
I see in the datasheet...
hi, i've used the official zephyr version till some days ago. the reset pin worked. now i've switched to the zephyr version "supported" by nordic and the pin reset isn't working...
I did the multilink central function when I used zephyr OS Connecting the five peripherals is stable at first, but after a while the error of <err> bt_att: ATT Timeout will...
