Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello everybody,
I'm trying to flash an example code (let's say the blinky one) from the SDK (15.3) onto the Arduino Nano 33 BLE board.
I know that is possible to flash...
Hello,
I'm trying to resolve an issue in my project.
It appears there is a memory leak.
In logs I can find the error code : 0xBFED
Do you know what that code is? ...
Hi,
I recently had a problem about timestamp that it's all 0 on the RTT Viewer.
And i 'm based on the nRF5_SDK_15.2.0\examples\peripheral\rtc to check the timesteamp....
Hi Nordic
I have some issue When using NRF52832 central to connect the NRF52832 peripheral.
i am following the SDK15.3.0 ble_app_uart & ble_app_uart_c to deign the central...
Hi
I have a question about LXFO input on external low swing clock setting using nRF52832.
I can see the input specification of external low swing clock about only peak...
Hi,
I am currently developing a stationary BLE device. I am testing the nRF52840-dongle in combination with the pc-ble-driver. For that purpose, I am using the connectivity_4...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am operating in a "peripheral" configuration, with bonding enabled. "BLE_GATTS_EVT_WRITE" occurs when notification is permitted...
We're porting over some software to the Arduino Nano 33 BLE Sense. This board comes with an nRF52840 clocked at a max. of 64MHz. However, the same code runs about 2x slower...
I want to send Tx power in advertisement packet.
Currently I am using following code.
int8_t txpower_level;
static ble_advertising_init_t init =
{
....
Customers use nrf52810 flash program to store data, but want to know what flash start and end address can be written, please point out that you can refer to that document...
Dear Nordic Semiconductor
I am using device:
NRF51802 bluetooth 4.0
Product Introduction:
Features:
1.Adopt NRF51802 bluetooth 4.0 BLE SOC
2.ARM CORTEX-M0
3...
Hi , I use the pc-ble-driver to developer desktop tools, like nRF Connect. Unfortunately, I don't know Java. I‘ve tried to used examples that work(heart_rate_collector and...
Hello,
We use a custom interface board to program and run test programs on our series of tiny BLE modules based on nRF52xxx series (ISP1507, ISP1807, ISP1907).
Our interface...
Hello ,
The test of CPS/SEN/SPE/BI-04-C [Procedure Already In Progress] failed.
While this test, the tester sometimes received the unexpected ATT Disconnect which our...
