Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
I am working with nRF Connect SDK using an nRF52840 DK. And I want to realise both BLE mesh and FOTA upgrade. FOTA upgrade example SMP Server Sample works properly for Bluetooth...
To parse information from strings I want to use sscanf().
Currently I have this small test program:
And in the prj.conf I have CONFIG_NEWLIB_LIBC=y defined.
This program...
Hi, At power on lots of MUCBoot prints pop out of the UART:
*** Booting Zephyr OS build v2.3.0-rc1-ncs1 *** <inf> mcuboot: Starting bootloader <inf> mcuboot: Primary image...
Hello -
We are developing an application for nRF52840, using the v17.0.0 SDK. The application is running on FreeRTOS. We need to power off all the RAM and use the RTC...
Hi, I am trying to get bootloader to jump to either application 1 or 2 base on button states when booting. I am not sure how do it properly. One of the applications is using...
I created an Azure IOT Hub and simulated a X.509 device using C and device SDK for Azure .
No problems here.
Then I run sample nRF9160: Azure Iot Hub and receive the...
I am using 2 counters, one to produce the 4MHz, and the other for the 62.5KHz, to drive I2S module.
I need to find a way to stop the first counter (4MHz) after it produces...
Hi All,
Currently I am using SDK_17.0.0 for nRF52832 with Softdevice S132_V7.0.1. I come to know about release of SDK_17.0.2 with highly recommendation to migrate from SDK_17...
Hi. I have the following code, I am attempting to read AIN0 on pin 4 (P0.02).
I am watching the result whilst debugging the application on DK52, and it is a random value...
I'm currently facing a problem while using FreeRTOS. I've created a task, but that tasks freezes the board at this line :
without FreeRTOS this piece of code works...
I've noticed three PCA10059 Dongles have failed in the past week. One on my desk and the two on a co-worker's desk. Its the same failure mode where everything appears to function...
Hi,
We are going to evaluate: nRF52840 with a large NOR flash. This Flash has two options: 3.0V / 50 mA max, Or 1.8V / 50 mA max. We prefere to use the 1.8V type, as this...
Hello!
I am new to developing with BLE so any help to this frustrating problem would be greatly appreciated!
Firstly, I am using SDK16, Soft Device 113, v.7.0.1 on a custom...
Hi. I'm designing a board like Thingy:91 for sensor driving based on nRF9160. In Thingy:91 Hardware files, the PCB has many blind vias. The production of HDI PCBs is very...
Looking for recommended PCB footprint drawing for nRF9160. LGA dimension drawing is available, but need the footprint for a PCB design.
Thank You,
Joe Norris
