Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
Hi,
In past we have observed BLE_HCI_LOCAL_HOST_TERMINATED_CONNECTION as a disconnection reason when the application layer tries to disconnect because of a timeout. But...
Hello, we are developing a project solution where we want to pass data between multiple sensor devices using BLE advertising data. For now, we have a test setup with two nrf52832dk...
Hi,
I would like to catch in main.c the nobody connect after advertising event via ADV_SET_TERMINATED.
I can see with breakpoint program jump into ble_advertising_on_ble_evt...
Hello
I am making a button double-click function in sdk v17. I've tried 'app_button' and 'app_timer'. Created a timer that is called every 0.1 seconds and terminates when...
Hi there,
To put a little bit of context, I've designed a wearable that is now going towards pre-production (only some minors fix left to do). In the last iteration, we...
Hi，all:
I use 9160DK to test PSM mode as follow steps with at_client example：
1、set ”AT+CFUN=0“ to power off mode;
2、set "AT+CPSMS=1,"","","10101010","00100001"" to...
Hello,
We're making RuuviTag sensor beacons which log environmental data to flash. Logged data is later read by a mobile phone application over Nordic UART Service.
The...
Hello
I am programming using the nrf52832 module 'MDBT42Q-512KV2' in SDK v17.0.
This works well without any problems in the example ble_app_blink. However, the BLE is...
Hello
I am contacting you to have a little more information concerning the messages which are sent in the examples thread_simple_coap_client and thread_simple_coap_server...
We have performed the DTM mode setup on the ATEX HW variant of nRF52832 chipset using nRF go studio application where the app is throwing an error as attached in the screenshot...
This is more related to the Segger Embedded Studio than Nordic parts or SDK, but I'd like to hear what kind of experience other Nordic users are having with the Segger IDE...
I want to run BME680 sensor example from zeyphyr->samples->sensors, i loaded the project with adding nrf9160dk_nrf9160ns overlay file with the contents :
&i2c2 { compatible...
Hi,
we are using the nRF52840 in a medical ECG recorder. To stream the data as fast as possible we want to use the 2Mb phy. Everything is working as expected under iOs and...
Hello,
I am using Nordic's SES 4.52 with a project from nRF Connect SDK 1.3.1. I have preprocessor definitions I'd like to add to the project to mirror those added on the...
The nRF9160 datasheet tells the reader to refer to the website for Altium files. However, the only files I can find are for the development board. Is it possible to release...
