When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello
I would like to transmit gps data to my website in addition to nrf cloud, there is a example or documentation about this that I can take of reference? I am working...
Hi I am New with nrf24l01+ and i made my first project it was working perfect with 2 nrf24l01+ without antenna . After the end of the project i change one of the nrf24l01...
I'm trying the given example < twi_sensor >. I connect nRF52 DK P0.26 to my sensor's SDA, nRF52 DK P0.27 connects to my sensor's SCL. My sensor runs at 400kHz, so I modified...
Hello, I'm new for mesh, have a question about the mesh dfu bootloader.
the source device of the mesh dfu shuld be connected to a host. how to assign the uart pin? is it...
I have to integrate a softdevice into an existing nrf52833 SES project. All the documentation I have found isstarting from any of the examples and using GNU Linker instead...
Hi,
I am trying to create an application for nrf52810 soc. I have a problem on selecting board name and the SDK version
I am having nrf52DK (nRF52832 soc) development...
Folks. I developed my own circuit using nRF 52833 and I`m trying to upload a new firmware via SWD interface. I'm not getting connected to the target for any reason. Is there...
Using SDK 17.0.2 and the nRF52840DK, I am setting up SPIM with a memory IC (not actually hooked up though, just looking at the signals on the oscilloscope). This code is executed...
I'm facing a problem with a product I'm developing. The problematic setup is as follows:
Two nRF52832 peripherals (S132 v6.0.0), each notifying on two characteristics...
Using: Windows Pro 10.0.19041 Build 19041
I'm trying to run Trace Collector for an issue with the nRF9160 and FOTA. I go to run the Trace Collector and it starts, but says...
I am using nRF52832. For reading ADC value for battery level percentage i have used 800k and 1M ressitor value. But while reading ADC Current cosumption is reached to 3 to...
I am trying to copy from this example:
https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode
but I get:
./nrf5_SDK_Current...
Hi,
I'm trying to understand the PSM availability of my local network.
After playing a bit with the RAT and RPTAU values, I found out that using RAT=16~30 secs and RPTAU...
