Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
To parse information from strings I want to use sscanf().
Currently I have this small test program:
And in the prj.conf I have CONFIG_NEWLIB_LIBC=y defined.
This program...
Hi, At power on lots of MUCBoot prints pop out of the UART:
*** Booting Zephyr OS build v2.3.0-rc1-ncs1 *** <inf> mcuboot: Starting bootloader <inf> mcuboot: Primary image...
Hello -
We are developing an application for nRF52840, using the v17.0.0 SDK. The application is running on FreeRTOS. We need to power off all the RAM and use the RTC...
Hi, I am trying to get bootloader to jump to either application 1 or 2 base on button states when booting. I am not sure how do it properly. One of the applications is using...
I created an Azure IOT Hub and simulated a X.509 device using C and device SDK for Azure .
No problems here.
Then I run sample nRF9160: Azure Iot Hub and receive the...
I am using 2 counters, one to produce the 4MHz, and the other for the 62.5KHz, to drive I2S module.
I need to find a way to stop the first counter (4MHz) after it produces...
Hi All,
Currently I am using SDK_17.0.0 for nRF52832 with Softdevice S132_V7.0.1. I come to know about release of SDK_17.0.2 with highly recommendation to migrate from SDK_17...
Hi. I have the following code, I am attempting to read AIN0 on pin 4 (P0.02).
I am watching the result whilst debugging the application on DK52, and it is a random value...
I'm currently facing a problem while using FreeRTOS. I've created a task, but that tasks freezes the board at this line :
without FreeRTOS this piece of code works...
I've noticed three PCA10059 Dongles have failed in the past week. One on my desk and the two on a co-worker's desk. Its the same failure mode where everything appears to function...
Hi,
We are going to evaluate: nRF52840 with a large NOR flash. This Flash has two options: 3.0V / 50 mA max, Or 1.8V / 50 mA max. We prefere to use the 1.8V type, as this...
Hello!
I am new to developing with BLE so any help to this frustrating problem would be greatly appreciated!
Firstly, I am using SDK16, Soft Device 113, v.7.0.1 on a custom...
Hi. I'm designing a board like Thingy:91 for sensor driving based on nRF9160. In Thingy:91 Hardware files, the PCB has many blind vias. The production of HDI PCBs is very...
Looking for recommended PCB footprint drawing for nRF9160. LGA dimension drawing is available, but need the footprint for a PCB design.
Thank You,
Joe Norris
Hi,
I want to use Bluetooth Mesh on the nRF9160dk and the mesh stack seems to work (I can provision and use a model with nRF Mesh 2.4.1 ) but when I provision a second nRF9160dk...
