Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Gentlemen:
I'm new to Nordic processors, but I have implemented projects with Silabs Gecko and ATTiny processors in the past. I'm working on a project for a consumer product...
Hello,
I have installed Embedded Studio and acquired a Nordic license. However the Tools/Options... nRF Connect menu option does not appear. I tried creating a dummy Nordic...
The project for nRF51822 was developed on base of example ble_peripheral ble_app_hrs for pca10028/s130 with an additional vendor specific service with 128-bit UUID for an...
I have a strange problem. We built 100 custom boards. I've only checked about 50 boards so far. 47 boards work properly. 3 do not.
We used secure_bootloader_uart_pca10056...
Hi support team
One of our customer ask if it's possible to transfer a file system(LittleFS,refer: https://github.com/ARMmbed/littlefs ) to our Soc?? If not, are there some...
I am new to BLE and I am exploring Introduction to service. However I am stuck with Step 1 and Step 2. Is Step 1: static ble_os_t m_our_service; (to declare a service) and...
I have a device with no OS on it that talks serial through a UART to a nRF53840. I need to be able to update the nRF53840's firmware across the serial link, but since I don...
Hello, I am working on the BMD-300 Series Evaluation Kit with nrf52832 microcontroller and I tried accessing the serial number of my nrf52832, with these functions:
m_device_id1...
One doubt, if a node gets reset or disconnected , due to power failure in openthead cli mesh, dose it need to get configured again to join the mesh or will it connect to mesh...
First, by "Custom Protocol" I just mean that I need to directly access the radio to transmit or receive single packets occasionally. The literature appears to indicate that...
Hi, We flashed an ncs v1.3.0-rc1 build onto a 5340 DK network core, and ever since then the UART is not sending any data to our PC. We have connected RxD and TxD to pins P0...
I've seen a few discussions on C++ support. It's frustrating I can't contribute to the conversation - I'm not sure if that's because my account is too new, or if comments...
Good day, support!
I have a couple of questions regarding the mandatory services of the nRF52840 dongle.
1) How to add characteristics to the mandatory services 0x1800...
Hii,
I am trying to flash secure_bootloader into my nRF 52 SDK. I am facing some issue.
can you please explain how to create "micro_ecc_lib_nrf52.a" file (which software...
