Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I'm using a NRF52832 QFAA connected to a Quectel modem through UART. We're using UARTSerial from Mbed OS 5.
We've produced 12 custom boards where on 2 of them the...
Hello,
I'm working on adding an HTS service to an existing device (nRF52832), and running into a problem that can be reproduced on PCA10040 and S132 5.0
When my code is...
I modified the firmware of our control unit to allow BLE communication. Now It communicates with an ANDROID APP. The chip used is nRF24L01+, It send and get only Non-Connectable...
Hello,
I'm trying out the HID Keyboard example (sdk 16.0.0, s132) and was able to pair once to my phone. Now I can't pair to any device. The following pop-up window appears...
I'm running SDK 14.2 using FreeRTOS on a nrf52832.
When I increase NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 158, the system ends up in Hard Fault.
Anyone have suggestions on...
Hello,
I am using an nRF52 to transfer 20 bytes (through notifications) to a raspberry pi (with bluetooth dongle). I've been experiencing some weird connection times: I...
Hi
I have 1 PCA10040 dev kit and 1 Raspberry Pi 3.
If I connect NRF dongle to Raspberry Pi will Raspberry Pi act as mesh-node ?
All I want to do is send data from PCA10040...
Hello,
nRF52840 is having the inbulit RTC for keeping the time.
Should i need to use external RTC with coin battery for even after power off the BLE nRF52840.
PLease...
Hi!
We're considering implementing some security measurements into our devices, and so naturally we've started to investigate CryptoCell and other Backends supported by...
Hello,
I recently updated nRF Connect to version 3.4.0 (Bluetooth Low Energy). I'm observing, that the tool is not able to reconnect to a peripheral that was previous bonded...
Hi Nordic Experts,
I use nRF52832 for a custom board, I use GPIO P0.17 and P0.18 for controlling NMOS switch, for buzzer and vibration motor, and the frequency is controlled...
So I seem to be having trouble interfacing with nrfl2401. To initially test the chip, I sent `0xFF` to be able to read off the status register but when I do, I get `0x1C`...
Hello Nordic Team,
We are working on a BLE project with RSL10 board from OnSemi. We need a BLE sniffer to capture and analyze the BLE packets in the air for debugging purposes...
