Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello Nordic;
I use SDK 17.0.2 and gls example . We know for security in pairing, considered a password which that is randomly generated in SoftDevice and sent to UART....
I am having problems loading an existing project that I successfully built and ran in the past.
I open IDE from nRF Connect > Toolchain Manager > Open IDE
The SES opens...
Hi,
Our Nordic app is doing BLE<->SPI communication.
All works fine when running in debug mode with SEGGER IDE.
Once we run without the debugger running, the SPI transmits...
Any idea why I need to send write enable twice, without reading the status in between, to get the write latch set?
It doesn't work this way, but if I change "#if 0"...
Hi,
I'm using nrf52840 on a custom board and have a sensor connected over the pins P0.9 and P0.10
which are NFC pins that have been converted to GPIO by using macro (CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
which hex file shall i install for an LTE application ?
It is basically step 7 of this tutorial: infocenter.nordicsemi.com/index.jsp
I wanna have a LTE application...
I am trying to start developing on my nRF52833 DK using Segger embedded studios, but my board does not show up as a mounted device on my laptop (echoed by the fact that Segger...
Hi there.
I am attempting to do some reallife tests on the nrf52840, mainly focusing on long-range capabilities and performance between the DK and an iPhone XS. Are there...
Hello, I've seen several posts about this, but I'm a little hesitant to use older posts since you guys put out new and improved versions pretty quickly. We are using SDK 16...
nRF52832 on a nRF52DK connectivity_4.1.1_1m_with_s132_5.1.0.hex pc_ble_driver_py v0.14.2
Steps to reproduce: - connect to a peer device - discover services and attributes...
hello :
1)The packet format of NRF52832 2.4G is as follows, I would like to ask whether the 2.4G CRC can be turned off.
I use two boards PTX and PRX to transmit each...
Hello fellow developers,
I'm developing the Bluetooth Low Energy (BLE) app with my own functions. Now I would like to pack it as a standalone Electron App, which can be...
Dear Sir,
I am working on NRF52 and I have DK of PCA10040 / V1.2.1 / 2017.36 / 682236729. I have done program advertising with scanning both in one program. then I used...
Hi, I have problem. My NRF52832 Dev board is not recognizable by anything. L05 diode is blinking every 0.5 sec. I used Segger - not recognized, Keid again J Flash same story...
