I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello.
When I try to import a project , it will show a error. I can't build it . Pleave view following info and help me about it . Thank you.
Harrison
BR!~
Hello,
I try to add the BLE-Template code into my existing program code, but I get the following linkage error. I have defined the following flash_placement.xml for my Segger...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
Hi,
Add BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event handle at ble_lbs service in example of ble_app_blinky. but when client read the characteristics 1524 or 1525, no BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
Environment: Windows 10 nRF Connect SDK 1.4.0 I followed all of the steps described in nRF connect SDK documentation and tried to build "Blinky" sample from zephyr as shown...
use s132 on NRF52832
when i used sd_ble_gap_connnect () to connected peripheral device,it return NRF_ERROR_INVALID_ADDR
the addr copyed in scan_evt_handler() by NRF_BLE_SCAN_EVT_FILTER_MATCH...
Hi ,
I have made basic binary sensor based on light bulb project,
wanted to add default BIND-TO-Gateway ( Short address 0x000). Gateway is CLI_AGENT .
I am try to add...
select at_client folder
west build -b nrf9160dk_nrf9160ns -p
shows this warning
```
warning: The choice symbol LTE_NETWORK_MODE_NBIOT (defined at /Users/paul_tanner...
Hello, we are using a usb dongle where we have a NRF52840 and RFX2401 PA+LNA frontend. The latter can be controlled with TX_EN and RX_EN pins. Please see attached schematic...
Hi there,
I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. Everything except one single thing is working. I've just implemented FDS...
I have installed the sdk v 1.4.0 via the toolchain manager (nrf connect 3.6.0). I am using windows 10.
Here are my problems :
First I dont have the launch ide button after...
Hello Team,
We have already done the PoC for the Openthread network. I have created a border router using nRF52840 as an NCP and multiple nRF52840 end devices.
Now my...
If I have a firmware project working reliably on the nRF52810, is it possible to build a single firmware image that will run on both the nRF52805 and the nRF52810? I'm not...
Hi,
I was trying to program my board using SEGGER, but it doesn't seem to be working (log provided in the picture below)
/resized-image/__size/320x240/__key/communityserver...
