According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
I am trying to set up a region of RAM to store variables that persist across soft reboots but am unsure how to do it in this environment. I would normally define a region...
Hi Nordic ppl,
Is Nordic SoC supporting BlueZ package ?
Any specific SoC that we should be selecting to be able to run the .
Also, i believe all 3rd party Modules...
I am trying to implement openthread cli uart in pca10059, have made all modifications but the hex file is not getting burnt in bootloader mode using nrfconnect
/cfs-file...
Hi:
I use the PCA1004 EVK bord to configuer the I2S MCK as 256K, 32MHz/125 (I2S_CONFIG_MCK_SETUP 34340864) .
then I measure the pin use oscilloscope, but I only get 255K...
Hi Nordic support,
We had an "intermittent" connection failure with a BLE radio in one of our products under development, which exhibited itself with an <unknown> device...
Hello,
We want to use the flash to store two types of information: application configuration settings (which should be protected during DFU) and temporary data (which...
Hi,
I m using nrf52840 and m doing DFU over serial.
one side is master controller and other end is NRF DFU serial(secure bootloader uart debug code).
After sending init...
Hi everyone,
I am trying to connect to a smartphone in an extended advertising using the firmware created under the following conditions. However, there are no event notifications...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am making an example of periodically reading sensor data using SPI.
The SPI is triggered through...
Currently I am using a PCA10040 to do some prototyping for a custom board. I intended to use the nrf52832 to interface with a HDC2010 (TI) temperature and humidity IC over...
Hi,
I was using SDK v1.1.0 for a while and am updating my project to SDK v1.2.0. I see that there is also a release for v1.3.0, however, there are too many application and...
I have tried to setup the time cluster, with:
ZB_ZCL_TIME_SET_REAL_TIME_CLOCK_CB(time_set_rtc);
But whn I do it, I lways get linking errors, since zb_scl_set_real_time_clock_callback...
I had a continuation question to this.
https://devzone.nordicsemi.com/f/nordic-q-a/64457/scheduler-for-thingy-91-using-nrf9160-dk
Is there any sample tutorial for the...
I don't think this is possible at the moment but worth putting it out in the wild:
Currently the binary image sizes for nRF9160 using Zephyr can get quite hefty. Is there...
